Pickup (music technology)
A pickup is a transducer that captures or senses mechanical vibrations produced by musical instruments, particularly stringed instruments such as the electric guitar, and converts these to an electrical signal that is amplified using an instrument amplifier to produce musical sounds through a loudspeaker in a speaker enclosure. The signal from a pickup can also be recorded directly.
Most electric guitars and electric basses use magnetic pickups. Acoustic guitars, upright basses and fiddles often use a piezoelectric pickup.
A typical magnetic pickup is a transducer (specifically a variable reluctance sensor) that consists of one or more permanent magnets (usually alnico or ferrite) wrapped with a coil of several thousand turns of fine enameled copper wire. The magnet creates a magnetic field which is focused by the pickup's pole piece or pieces. The permanent magnet in the pickup magnetises the guitar string above it. So the string is, in essence, a magnet itself and its magnetic field is in alignment with that of the permanent magnet that magnetized it. When the string is plucked, the magnetic field around it moves up and down with the string. This moving magnetic field induces a current in the coil of the pickup.
The pickup is connected with a patch cable to an amplifier, which amplifies the signal to a sufficient magnitude of power to drive a loudspeaker. A pickup can also be connected to recording equipment via a patch cable.
The pickup is most often mounted on the body of the instrument, but can be attached to the bridge, neck or pickguard.
Pickups have magnetic polepieces (with the notable exceptions of rail and lipstick tube pickups—one or two for each string), approximately centered on each string. (The standard pickups on the Fender Jazz Bass and Precision Bass have two polepieces per string, to either side of each string.)
On most guitars, the strings are not fully parallel: they converge at the nut and diverge at the bridge. Thus, bridge, neck and middle pickups usually have different polepiece spacings on the same guitar.
There are several standards on pickup sizes and string spacing between the poles. Spacing is measured either as a distance between 1st to 6th polepieces' centers (this is also called "E-to-E" spacing), or as a distance between adjacent polepieces' centers.
(Vintage Gibson guitars)
(Most Fender guitars, modern Gibson, Floyd Rose bridges)
|Very close to bridge, extra pickup
(Roland GK series hexaphonic)
(Fender Telecaster guitars)
|Steinberger Spirit GT-Pro spacing
(may be typical for other Steinberger guitars)
Some high-output pickups employ very strong magnets, thus creating more flux and thereby more output. This can be detrimental to the final sound because the magnet's pull on the strings can cause problems with intonation as well as damp the strings and reduce sustain.
Other high-output pickups have more turns of wire to increase the voltage generated by the string's movement. However, this also increases the pickup's output resistance/impedance, which can affect high frequencies if the pickup is not isolated by a buffer amplifier or a DI unit.
The turns of wire in proximity to each other have an equivalent self-capacitance that, when added to any cable capacitance present, resonates with the inductance of the winding. This resonance can accentuate certain frequencies, giving the pickup a characteristic tonal quality. The more turns of wire in the winding, the higher the output voltage but the lower this resonance frequency. The inductive source impedance inherent in this type of transducer makes it less linear than other forms of pickups, such as piezo-electric or optical.
The external load usually consists of resistance (the volume and tone potentiometers in the guitar, and any resistance to ground at the amplifier input) and capacitance between the hot lead and shield in the guitar cable. The electric cable also has a capacitance, which can be a significant portion of the overall system capacitance. This arrangement of passive components forms a resistively-damped second-order low-pass filter. Pickups are usually designed to feed a high input impedance, typically a megohm or more, and a low-impedance load reduces the high-frequency response of the pickup because of the filtering effect of the inductance.
Single-coil pickups act like a directional antenna and are prone to pick up mains hum — nuisance alternating current electromagnetic interference from electrical power cables, power transformers, fluorescent light ballasts, video monitors or televisions — along with the musical signal. Mains hum consists of a fundamental signal at a nominal 50 or 60 Hz, depending on local current frequency, and usually some harmonic content.
To overcome this, the humbucking pickup was invented by Joseph Raymond "Ray" Butts, but Seth Lover of Gibson was also working on one. Who developed it first is a matter of some debate, but Ray Butts was awarded the first patent (U.S. Patent 2,892,371) and Seth Lover came next (U.S. Patent 2,896,491).
A humbucking pickup is composed of two coils, with each coil wound reverse to the other. Each set of six magnetic poles is also opposite in polarity. Since ambient hum from electrical devices reaches the coils as common-mode noise, it induces an equal voltage in each coil, but 180 degrees out of phase between the two voltages. These effectively cancel each other, while the signal from the guitar string is doubled.
When wired in series, as is most common, the overall inductance of the pickup is increased, which lowers its resonance frequency and attenuates the higher frequencies, giving a less trebly tone (i.e., "fatter") than either of the two component single-coil pickups would give alone.
An alternative wiring places the coils in buck parallel, which has a more neutral effect on resonant frequency. This pickup wiring is rare, as guitarists have come to expect that humbucking pickups 'have a sound', and are not so neutral. On fine jazz guitars, the parallel wiring produces significantly cleaner sound, as the lowered source impedance drives capacitive cable with lower high frequency attenuation.
A side-by-side humbucking pickup senses a wider section of each string than a single-coil pickup. By picking up a larger portion of the vibrating string, more lower harmonics are present in the signal produced by the pickup in relation to high harmonics, resulting in a "fatter" tone. Humbucking pickups in the narrow form factor of a single coil, designed to replace single-coil pickups, have the narrower aperture resembling that of a single coil pickup. Some models of these single-coil-replacement humbuckers produce more authentic resemblances to classic single-coil tones than full-size humbucking pickups of a similar inductance.
Most electric guitars have two or three magnetic pickups. A combination of pickups is called a pickup configuration, usually notated by writing out the pickup types in order from bridge pickup through mid pickup(s) to neck pickup, using “S” for single-coil and “H” for humbucker.
Common pickup configurations include:
Less frequently found configurations are:
- S (Fender Esquire, early Gibson Les Paul Juniors, Gibson Melody Maker, Danelectro U1, some Telecasters)
- H (Gibson ES-165 Herb Ellis, Kramer Baretta, later Les Paul Juniors)
- H-S (Hamer Californian Deluxe, Les Paul BFG, Squier '51)
- H-H-H (some Gibson Les Paul Goldtop and Custom models, Gibson SG-3, Gibson ES-5 Switchmaster (after 1957), Kramer Jersey Star, Ibanez Destroyer, Ibanez PGM200)
Examples of rare configurations that only a few particular models use include:
- H-S, but with single coil in the middle (one model of Fender Jazzmaster, Ibanez RG2011SC, Fender Player Jaguar)
- H-S-S, but with no space between the middle single coil and the bridge humbucker (Hamer Phantom with angled neck pickup)
- H-H-S (Mayones Legend “22” Anders Nyström signature, some ESP Stephen Carpenter Models, and Alembic Jerry Garcia Models)
- H-S-S-H (Music Man Steve Morse Signature)
- S-H (some Telecasters, Music Man “Valentine” James Valentine signature)
- S-H-H (some early seven-string ESP Horizons)
- S-H-S (Fender Wayne Kramer Signature)
Many semi-acoustic and acoustic guitars, and some electric guitars and basses, have been fitted with piezoelectric pickups instead of, or in addition to, magnetic pickups. These have a very different sound, and also have the advantage of not picking up any other magnetic fields, such as mains hum and feedback from monitoring loops. In hybrid guitars, this system allows switching between magnetic pickup and piezo sounds, or simultaneously blending the output. Solid bodied guitars with only a piezo pickup are known as silent guitars, which are usually used for practicing by acoustic guitarists. Piezo pickups can also be built into electric guitar bridges for conversion of existing instruments.
Most pickups for bowed string instruments, such as cello, violin, and double bass, are piezoelectric. These may be inlaid into the bridge, laid between the bridge feet and the top of the instrument, or, less frequently, wedged under a wing of the bridge. Some pickups are fastened to the top of the instrument with removable putty.
Piezoelectric pickups have a very high output impedance and appear as a capacitance in series with a voltage source. They therefore often have an instrument-mounted buffer amplifier fitted to maximize frequency response.
The piezo pickup gives a very wide frequency range output compared to the magnetic types and can give large amplitude signals from the strings. For this reason, the buffer amplifier is often powered from relatively high voltage rails (about ±9 V) to avoid distortion due to clipping. A less linear preamp (like a single-FET amplifier) might be preferable due to softer clipping characteristics. Such an amplifier starts to distort sooner, which makes the distortion less "buzzy" and less audible than a more linear, but less forgiving op-amp. However, at least one study indicates that most people can not tell the difference between FET and op-amp circuits in blind listening comparisons of electric instrument preamps, which correlates with results of formal studies of other types of audio devices. Sometimes, piezoelectric pickups are used in conjunction with magnetic types to give a wider range of available sounds.
For early pickup devices using the piezoelectric effect, see phonograph.
Some pickup products are installed and used similarly to piezoelectric pickups, but use different underlying technology, for instance electret or condenser microphone technology.
Double systems pickups
There are basically four principles used to convert sound into an alternating current, each with their pros and cons:
- A microphone registers the vibrations of the air caused by the instrument. In general this technique guarantees a good sound quality, but with two limitations: feedback and crosstalk.
- Contact pickups register the vibrations of the instrument itself. They have the advantage of producing little feedback and no crosstalk at all. In spite of their lesser sound quality and thanks to their low price, contact pickups (and especially the piezoelectric pickup) have become the most popular transducer.
- Magnetic pickups. Magnetic pickups, as applied in electric guitars, register the vibrations of nickel or steel strings in a magnetic field. They have the advantage that they can be connected directly to an (electric guitar) amplifier, but in combination with a steel-string acoustic guitar the sound tends to be electric. This is why acoustic guitarists typically choose a piezoelectric pickup, built in microphone, or both.
- Electrostatic pickups. Another way is to use the changing capacitance between the string and a pickup plate. These electronic pickups produce much higher dynamics than conventional pickups, so the difference between a soft and a loud pick strike is more pronounced than with other types of pickups.
An amplification system with two transducers combines the qualities of both. A combination of a microphone and a piezoelectric pickup typically produces better sound quality and less sensitivity to feedback, as compared to single transducers. However, this is not always the case. A less frequently used combination is a piezoelectric and a magnetic pickup. This combination can work well for a solid sound with dynamics and expression. Examples of a double system amplifier are the Highlander iP-2, the Verweij VAMP or the LR Baggs dual source and the D-TAR Multisource.
Hexaphonic pickups (also called divided pickups and polyphonic pickups) have a separate output for each string (Hexaphonic assumes six strings, as on a guitar). This allows for separate processing and amplification for each string. It also allows a converter to sense the pitch coming from individual string signals for producing note commands, typically according to the MIDI (musical instrument digital interface) protocol. A hexaphonic pickup and a converter are usually components of a guitar/synthesizer.
Such pickups are uncommon (compared to normal ones), and only a few notable models exist, like the piezoelectric pickups on the Moog Guitar. Hexaphonic pickups can be either magnetic or piezoelectric or based on the condensor principle like electronicpickups
Optical pickups are a fairly recent development that work by sensing the interruption of a light beam by a vibrating string. The light source is usually an LED, and the detector is a photodiode or phototransistor. These pickups are completely resistant to magnetic or electric interference and also have a very broad and flat frequency response, unlike magnetic pickups.
Optical pickup guitars were first shown at the 1969 NAMM in Chicago, by Ron Hoag.
In 2000, Christopher Willcox, founder of LightWave Systems, unveiled a new beta technology for an optical pickup system using infrared light. In May 2001, LightWave Systems released their second generation pickup, dubbed the "S2."
Active and passive pickups
Pickups can be either active or passive. Pickups, apart from optical types, are inherently passive transducers. "Passive" pickups are usually wire wound around a magnet, and are the most common type used. They can generate electric potential without need for external power, though their output is relatively low, and the harmonic content of output depends greatly on the winding.
"Active" pickups incorporate electronic circuitry to modify the signal. Active circuits are able to filter, attenuate or boost the signal from the pickup. The main disadvantage of an active system is requirement of a battery power source to operate the preamp circuitry. Batteries limit circuit design and functionality, in addition to being inconvenient to the musician. The circuitry may be as simple as a single transistor, or up to several operational amplifiers configured as active filters, active EQ and other sound-shaping features. The op amps used must be of a low-power design to optimize battery life, a design restriction that limits the dynamic range of the circuit. The active circuitry may contain audio filters, which reduce the dynamic range and mildly distort certain ranges. High-output active pickup systems also have an effect on an amplifier's input circuit.
Stereo and multiple pickups with individual outputs
Rickenbacker was the first manufacturer to market stereo instruments (guitars and basses). Their proprietary "Ric-O-Sound" circuitry has two separate output jacks, allowing the musician to send each pickup to its own audio chain (effects device, amplifier, mix console input).
Teisco produced a guitar with a stereo option. Teisco divided the two sections in the upper three strings and the lower three strings for each individual output.
The Gittler guitar was an experimental guitar with six pickups, one for each string.
Gibson created the HD.6X Pro guitar that captures a separate signal for each individual string and sends them to an onboard analog/digital converter, then out of the guitar via Cat 5 Ethernet Cable.
- Lawing, A Scott. "How Does a Pickup Really Work?". Lawing Musical Products. Dr A. Scott Lawing. Retrieved 2 January 2019.
- "Guitar Pickup - MagLab". nationalmaglab.org. Retrieved 2 January 2019.
- Wheeler. p.214
- Tillman, Donald (2002).
- Discrete FET Guitar Preamp
- Mottola, R.M. (2003). "A Listening Evaluation of Discrete vs Integrated Circuit Audio Preamplifiers in Stringed Musical Instruments". Journal of Musical Instrument Technology (23).
- B-Band electret pickup
- Schertler Bluestick
- "LightWave Systems | Technology". Retrieved 13 September 2012.
- Wallace, Joe (2006-12-11). "Light Speed Guitars: The Story Of Ron Hoag And His Optical Guitar Pickup". Gearwire. Archived from the original on 2009-05-01. Retrieved 2009-06-09.
- "About | LightWave Systems". Retrieved 2012-09-13.
- Brosnac, Donald (1980). Guitar Electronics: A Workbook. Ojai, CA: d.B. Music Co. ISBN 0-933224-02-8.
- Tillman, Donald (2002). Response Effects of Guitar Pickup Position and Width
- Wheeler, Tom (1992). American Guitars: an illustrated history. Harper. New York ISBN 0-06-273154-8
|Wikimedia Commons has media related to Guitar pickups.|