List of International Organization for Standardization standards, 1-4999

This is a list of published[Note 1] International Organization for Standardization (ISO) standards and other deliverables.[Note 2] For a complete and up-to-date list of all the ISO standards, see the ISO catalogue.[1]

The standards are protected by copyright and most of them must be purchased. However, about 300 of the standards produced by ISO and IEC's Joint Technical Committee 1 (JTC1) have been made freely and publicly available.[2]

ISO 1 – ISO 99

  • ISO 1:2016 Geometrical product specifications (GPS) - Standard reference temperature for the specification of geometrical and dimensional properties
  • ISO 2:1973 Textiles – Designation of the direction of twist in yarns and related products
  • ISO 3:1973 Preferred numbers – Series of preferred numbers
  • ISO 4:1997 Information and documentation – Rules for the abbreviation of title words and titles of publications
  • ISO 5 Photography and graphic technology – Density measurements
  • ISO 6:1993 Photography – Black-and-white pictorial still camera negative film/process systems – Determination of ISO speed
  • ISO 7 Pipe threads where pressure-tight joints are made on the threads
  • ISO 8:1977 Documentation – Presentation of periodicals
  • ISO 9:1995 Information and documentation – Transliteration of Cyrillic characters into Latin characters – Slavic and non-Slavic languages
  • ISO 11:1987 Aircraft – Ground pressure testing connections for pressure cabins
  • ISO 12:1987 Aerospace – Pipelines – Identification
  • ISO 14:1982 Straight-sided splines for cylindrical shafts with internal centering – Dimensions, tolerances and verification
  • ISO 15:2017 Rolling bearings – Radial bearings – Boundary dimensions, general plan
  • ISO 16:1975 Acoustics – Standard tuning frequency (Standard musical pitch)
  • ISO 17:1973 Guide to the use of preferred numbers and of series of preferred numbers
  • ISO 18:1981 Documentation – Contents list of periodicals
  • ISO 21:1985 Shipbuilding – Inland navigation – Cable-lifters for stud-link anchor chains
  • ISO 22:1991 Belt drives – Flat transmission belts and corresponding pulleys – Dimensions and tolerances
  • ISO 23:1993 Cinematography—Camera usage of 35 mm motion-picture film—Specifications
  • ISO 25:1994 Cinematography—Camera usage of 16 mm motion-picture film—Specifications
  • ISO 26:1993 Cinematography—Projector usage of 16 mm motion-picture films for direct front projection—Specifications
  • ISO 28:1976 Cinematography—Camera usage of 8 mm Type R motion-picture film—Specifications
  • ISO 29:1980 Cinematography—Projector usage of 8 mm Type R silent motion-picture film for direct front projection—Specifications [Withdrawn without replacement]
  • ISO 31 Quantities and units [withdrawn: replaced with ISO/IEC 80000]
  • ISO 32:1977 Gas cylinders for medical use—Marking for identification of content
  • ISO 34 Rubber, vulcanized or thermoplastic—Determination of tear strength
    • ISO 34-1:2015 Part 1: Trouser, angle and crescent test pieces
    • ISO 34-2:2015 Part 2: Small (Delft) test pieces
  • ISO 35:2004 Natural rubber latex concentrate—Determination of mechanical stability
  • ISO 36:2017 Rubber, vulcanized or thermoplastic—Determination of adhesion to textile fabrics
  • ISO 37:2011 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
  • ISO 41:1980 Shipbuilding—Inland vessels—Covers for deck openings for pumps [withdrawn without replacement]
  • ISO 43:2016 Aircraft—Jacking pads
  • ISO 44:1975 Aerospace—Lever-operated, two-position, ON/OFF switches—Directions of operation
  • ISO 45:1990 Aircraft—Pressure refuelling connections
  • ISO 46:1973 Aircraft—Fuel nozzle grounding plugs and sockets
  • ISO 48:2010 Rubber, vulcanized or thermoplastic—Determination of hardness (hardness between 10 IRHD and 100 IRHD)
  • ISO 49:1994 Malleable cast iron fittings threaded to ISO 7-1
  • ISO 50:1977 Metal pipes—Steel sockets screwed according to ISO 7 [Withdrawn without replacement]
  • ISO 53:1998 Cylindrical gears for general and heavy engineering—Standard basic rack tooth profile
  • ISO 54:1996 Cylindrical gears for general engineering and for heavy engineering—Modules
  • ISO 55:1977 Seedlac—Specification [Withdrawn without replacement]
  • ISO 57:1975 Bleached lac—Specification [Withdrawn without replacement]
  • ISO 60:1977 Plastics—Determination of apparent density of material that can be poured from a specified funnel
  • ISO 61:1976 Plastics—Determination of apparent density of moulding material that cannot be poured from a specified funnel
  • ISO 62:2008 Plastics—Determination of water absorption
  • ISO 63:1975 Flat transmission belts—Lengths [Withdrawn: Replaced with ISO 22]
  • ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1
  • ISO 67:1981 Muscovite mica blocks, thins and films—Grading by size [Withdrawn without replacement]
  • ISO 68 ISO general-purpose screw threads – Basic profile
    • ISO 68-1:1998 Part 1: Metric screw threads
    • ISO 68-2:1998 Part 2: Inch screw threads
  • ISO 69:1998 Cinematography—16 mm motion-picture and magnetic film—Cutting and perforating dimensions
  • ISO 70:1981 Cinematography—35 mm negative photographic sound record on 35 mm motion-picture film—Position and maximum width dimensions
  • ISO 71:2014 Cinematography—16 mm negative photographic sound record on 16 mm, 35/16 mm and 35/32 mm motion-picture film—Positions and dimensions
  • ISO 74:1976 Cinematography—Image area produced by camera aperture and maximum projectable image area on 8 mm Type R motion-picture film—Positions and dimensions
  • ISO 75 Plastics—Determination of temperature of deflection under load
    • ISO 75-1:2013 Part 1: General test method
    • ISO 75-2:2013 Part 2: Plastics and ebonite
    • ISO 75-3:2004 Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
  • ISO 76:2006 Rolling bearings—Static load ratings
  • ISO 78 Chemistry — Layouts for standards[Note 3]
    • ISO 78-2:1999 Part 2: Methods of chemical analysis
    • ISO 78-3:1983 Part 3: Standard for molecular absorption spectrometry [Withdrawn without replacement]
    • ISO 78-4:1983 Part 4: Standard for atomic absorption spectrometric analysis [Withdrawn without replacement]
  • ISO/TR 79:2015 Reference materials - Examples of reference materials for qualitative properties
  • ISO 82:1974 Steel—Tensile testing [Withdrawn: replaced with ISO 6892-1]
  • ISO 83:1976 Steel—Charpy impact test (U-notch) [Withdrawn: replaced with ISO 148-1]
  • ISO 86:1974 Steel—Tensile testing of sheet and strip less than 3 mm and not less than 0,5 mm thick [Withdrawn: replaced with ISO 6892-1]
  • ISO 89:1974 Steel—Tensile testing of wire [Withdrawn: replaced with ISO 6892-1]
  • ISO 90 Light gauge metal containers—Definitions and determination of dimensions and capacities
    • ISO 90-1:1997 Part 1: Open-top cans
    • ISO 90-2:1997 Part 2: General use containers
    • ISO 90-3:2000 Part 3: Aerosol cans
  • ISO 91 Petroleum measurement tables [Withdrawn: replaced with ISO 91:2017]
    • ISO 91-1:1992 Part 1: Tables based on reference temperatures of 15 degrees C and 60 degrees F
    • ISO 91-2:1991 Part 2: Tables based on a reference temperature of 20 degrees C
  • ISO 91:2017 Petroleum and related products - Temperature and pressure volume correction factors (petroleum measurement tables) and standard reference conditions
  • ISO 92:1976 Textile machinery and accessories—Spinning machinery—Definition of side (left or right)
  • ISO 93 Textile machinery and accessories—Cylindrical sliver cans
    • ISO 93-1:2006 Part 1: Main dimensions
    • ISO 93-2:2006 Part 2: Spring bottoms
  • ISO 94:1982 Textile machinery and accessories—Spindle gauges for ring-spinning and ring-doubling frames
  • ISO 96 Textile machinery and accessories—Rings and travellers for ring spinning and ring twisting frames
    • ISO 96-1:2016 Part 1: Flange rings T and SF and their travellers
    • ISO 96-2:2009 Part 2: HZ- and J-rings and their travellers
  • ISO 97:1975 Textile machinery and accessories—Rings for spinning, doubling and twisting for ear-shaped travellers [Withdrawn: replaced with ISO 96-2]
  • ISO 98:2001 Textile machinery and accessories—Spinning preparatory and spinning machinery—Main dimensions of coverings for top rollers

ISO 100 – ISO 199

  • ISO 100:1984 Pulleys for flat transmission belts—Crowns [Withdrawn: replaced with ISO 22]
  • ISO 102:1990 Aircraft—Gravity filling orifices
  • ISO 104:2015 Rolling bearings—Thrust bearings—Boundary dimensions, general plan
  • ISO 105 Textiles — Tests for colour fastness
    • ISO 105-A01:2010 Part A01: General principles of testing
    • ISO 105-A02:1993 Part A02: Grey scale for assessing change in colour
    • ISO 105-A03:1993 Part A03: Grey scale for assessing staining
    • ISO 105-A04:1989 Part A04: Method for the instrumental assessment of the degree of staining of adjacent fabrics
    • ISO 105-A05:1996 Part A05: Instrumental assessment of change in colour for determination of grey scale rating
    • ISO 105-A06:1995 Part A06: Instrumental determination of 1/1 standard depth of colour
    • ISO 105-A08:2001 Part A08: Vocabulary used in colour measurement
    • ISO 105-A11:2012 Part A11: Determination of colour fastness grades by digital imaging techniques
    • ISO 105-B01:2014 Part B01: Colour fastness to light: Daylight
    • ISO 105-B02:2014 Part B02: Colour fastness to artificial light: Xenon arc fading lamp test
    • ISO 105-B03:1994 Part B03: Colour fastness to weathering: Outdoor exposure
    • ISO 105-B04:1994 Part B04: Colour fastness to artificial weathering: Xenon arc fading lamp test
    • ISO 105-B05:1993 Part B05: Detection and assessment of photochromism
    • ISO 105-B06:1998 Part B06: Colour fastness and ageing to artificial light at high temperatures: Xenon arc fading lamp test
    • ISO 105-B07:2009 Part B07: Colour fastness to light of textiles wetted with artificial perspiration
    • ISO 105-B08:1995 Part B08: Quality control of blue wool reference materials 1 to 7
    • ISO 105-B10:2011 Part B10: Artificial weathering—Exposure to filtered xenon-arc radiation
    • ISO 105-C06:2010 Part C06: Colour fastness to domestic and commercial laundering
    • ISO 105-C07:1999 Part C07: Colour fastness to wet scrubbing of pigment printed textiles
    • ISO 105-C08:2010 Part C08: Colour fastness to domestic and commercial laundering using a non-phosphate reference detergent incorporating a low-temperature bleach activator
    • ISO 105-C09:2001 Part C09: Colour fastness to domestic and commercial laundering—Oxidative bleach response using a non-phosphate reference detergent incorporating a low temperature bleach activator
    • ISO 105-C10:2006 Part C10: Colour fastness to washing with soap or soap and soda
    • ISO 105-C12:2004 Part C12: Colour fastness to industrial laundering
    • ISO 105-D01:2010 Part D01: Colour fastness to drycleaning using perchloroethylene solvent
    • ISO 105-D02:2016 Part D02: Colour fastness to rubbing: Organic solvents
    • ISO 105-E01:2013 Part E01: Colour fastness to water
    • ISO 105-E02:2013 Part E02: Colour fastness to sea water
    • ISO 105-E03:2010 Part E03: Colour fastness to chlorinated water (swimming-pool water)
    • ISO 105-E04:2013 Part E04: Colour fastness to perspiration
    • ISO 105-E05:2010 Part E05: Colour fastness to spotting: Acid
    • ISO 105-E06:2006 Part E06: Colour fastness to spotting: Alkali
    • ISO 105-E07:2010 Part E07: Colour fastness to spotting: Water
    • ISO 105-E08:1994 Part E08: Colour fastness to hot water
    • ISO 105-E09:2010 Part E09: Colour fastness to potting
    • ISO 105-E10:1994 Part E10: Colour fastness to decatizing
    • ISO 105-E11:1994 Part E11: Colour fastness to steaming
    • ISO 105-E12:2010 Part E12: Colour fastness to milling: Alkaline milling
    • ISO 105-E13:1994 Part E13: Colour fastness to acid-felting: Severe
    • ISO 105-E14:1994 Part E14: Colour fastness to acid-felting: Mild
    • ISO 105-E16:2006 Part E16: Colour fastness to water spotting on upholstery fabrics
    • ISO 105-F01:2001 Part F01: Specification for wool adjacent fabric
    • ISO 105-F02:2009 Part F02: Specification for cotton and viscose adjacent fabrics
    • ISO 105-F03:2001 Part F03: Specification for polyamide adjacent fabric
    • ISO 105-F04:2001 Part F04: Specification for polyester adjacent fabric
    • ISO 105-F05:2001 Part F05: Specification for acrylic adjacent fabric
    • ISO 105-F06:2000 Part F06: Specification for silk adjacent fabric
    • ISO 105-F07:2001 Part F07: Specification for secondary acetate adjacent fabric
    • ISO 105-F09:2009 Part F09: Specification for cotton rubbing cloth
    • ISO 105-F10:1989 Part F10: Specification for adjacent fabric: Multifibre
    • ISO 105-G01:2016 Part G01: Colour fastness to nitrogen oxides
    • ISO 105-G02:1993 Part G02: Colour fastness to burnt-gas fumes
    • ISO 105-G03:1993 Part G03: Colour fastness to ozone in the atmosphere
    • ISO 105-G04:2016 Part G04: Colour fastness to oxides of nitrogen in the atmosphere at high humidities
    • ISO 105-J01:1997 Part J01: General principles for measurement of surface colour
    • ISO 105-J02:1997 Part J02: Instrumental assessment of relative whiteness
    • ISO 105-J03:2009 Part J03: Calculation of colour differences
    • ISO 105-J05:2007 Part J05: Method for the instrumental assessment of the colour inconstancy of a specimen with change in illuminant (CMCCON02)
    • ISO 105-N01:1993 Part N01: Colour fastness to bleaching: Hypochlorite
    • ISO 105-N02:1993 Part N02: Colour fastness to bleaching: Peroxide
    • ISO 105-N03:1993 Part N03: Colour fastness to bleaching: Sodium chlorite (mild)
    • ISO 105-N04:1993 Part N04: Colour fastness to bleaching: Sodium chlorite (severe)
    • ISO 105-N05:1993 Part N05: Colour fastness to stoving
    • ISO 105-P01:1993 Part P01: Colour fastness to dry heat (excluding pressing)
    • ISO 105-P02:2002 Part P02: Colour fastness to pleating: Steam pleating
    • ISO 105-S01:1993 Part S01: Colour fastness to vulcanization: Hot air
    • ISO 105-S02:1993 Part S02: Colour fastness to vulcanization: Sulfur monochloride
    • ISO 105-S03:1993 Part S03: Colour fastness to vulcanization: Open steam
    • ISO 105-X01:1993 Part X01: Colour fastness to carbonizing: Aluminium chloride
    • ISO 105-X02:1993 Part X02: Colour fastness to carbonizing: Sulfuric acid
    • ISO 105-X04:1994 Part X04: Colour fastness to mercerizing
    • ISO 105-X05:1994 Part X05: Colour fastness to organic solvents
    • ISO 105-X06:1994 Part X06: Colour fastness to soda boiling
    • ISO 105-X07:1994 Part X07: Colour fastness to cross-dyeing: Wool
    • ISO 105-X08:1994 Part X08: Colour fastness to degumming
    • ISO 105-X09:1993 Part X09: Colour fastness to formaldehyde
    • ISO 105-X10:1993 Part X10: Assessment of migration of textile colours into polyvinyl chloride coatings
    • ISO 105-X11:1994 Part X11: Colour fastness to hot pressing
    • ISO 105-X12:2016 Part X12: Colour fastness to rubbing
    • ISO 105-X13:1994 Part X13: Colour fastness of wool dyes to processes using chemical means for creasing, pleating and setting
    • ISO 105-X14:1994 Part X14: Colour fastness to acid chlorination of wool: Sodium dichloroisocyanurate
    • ISO 105-X16:2016 Part X16: Colour fastness to rubbing—Small areas
    • ISO 105-X18:2007 Part X18: Assessment of the potential to phenolic yellowing of materials
    • ISO 105-Z01:1993 Part Z01: Colour fastness to metals in the dye-bath: Chromium salts
    • ISO 105-Z02:1993 Part Z02: Colour fastness to metals in the dye-bath: Iron and copper
    • ISO 105-Z03:1996 Part Z03: Intercompatibility of basic dyes for acrylic fibres
    • ISO 105-Z04:1995 Part Z04: Dispersibility of disperse dyes
    • ISO 105-Z05:1996 Part Z05: Determination of the dusting behaviour of dyes
    • ISO 105-Z06:1998 Part Z06: Evaluation of dye and pigment migration
    • ISO 105-Z07:1995 Part Z07: Determination of application solubility and solution stability of water-soluble dyes
    • ISO 105-Z08:1995 Part Z08: Determination of solubility and solution stability of reactive dyes in the presence of electrolytes
    • ISO 105-Z09:1995 Part Z09: Determination of cold water solubility of water-soluble dyes
    • ISO 105-Z10:1997 Part Z10: Determination of relative colour strength of dyes in solution
    • ISO 105-Z11:1998 Part Z11: Evaluation of speckiness of colorant dispersions
  • ISO 108:1976 Textile machinery and accessories—Weaving looms—Definition of left and right sides
  • ISO 109:1982 Textile machinery—Working widths of weaving machines
  • ISO 110:1978 Textile machinery and accessories—Cones for yarn winding (cross wound) – Half angle of the cone 9 degrees 15' [Withdrawn without replacement]
  • ISO 111:1978 Textile machinery and accessories—Cones for yarn winding (cross wound) – Half angle of the cone 4 degrees 20' [Withdrawn: Replaced with ISO 8489-3]
  • ISO 112:1983 Textile machinery and accessories—Cones for yarn winding (cross wound) – Half angle of the cone 3 degrees 30' [Withdrawn: Replaced with ISO 8489-2]
  • ISO 113:2010 Rolling bearings—Plummer block housings—Boundary dimensions
  • ISO 114:1980 99.8 Unalloyed magnesium ingots—Chemical composition [Withdrawn: Replaced by ISO 8287]
  • ISO 115:2003 Unalloyed aluminium ingots for remelting—Classification and composition
  • ISO 119:1977 Plastics—Phenol-formaldehyde mouldings—Determination of free phenols—Iodometric method
  • ISO 120:1977 Plastics—Phenol-formaldehyde mouldings—Determination of free ammonia and ammonium compounds—Colorimetric comparison method
  • ISO 121:1980 Magnesium-aluminium-zinc alloy ingots and alloy castings—Chemical composition and mechanical properties of sand cast reference test bars [Withdrawn: replaced by ISO 16220]
  • ISO 123:2001 Rubber latex—Sampling
  • ISO 124:2014 Latex, rubber—Determination of total solids content
  • ISO 125:2011 Natural rubber latex concentrate—Determination of alkalinity
  • ISO 126:2005 Natural rubber latex concentrate—Determination of dry rubber content
  • ISO 127:2012 Rubber, natural latex concentrate—Determination of KOH number
  • ISO 128 Technical product documentation (TPD)—General principles of presentation[Note 3]
  • ISO 129 Technical product documentation (TPD)—Indication of dimensions and tolerances[Note 3]
    • ISO 129-1:2004 Part 1: General principles
    • ISO 129-4:2013 Part 4: Dimensioning of shipbuilding drawings
  • ISO 131:1979 Acoustics—Expression of physical and subjective magnitudes of sound or noise in air [Withdrawn without replacement]
  • ISO 132:2017 Rubber, vulcanized or thermoplastic—Determination of flex cracking and crack growth (De Mattia)
  • ISO 133:1983 Rubber, vulcanized—Determination of crack growth (De Mattia) [Withdrawn: Replaced with ISO 132]
  • ISO 136:1972 Steel—Simple torsion testing of wire [Withdrawn replaced by ISO 7800]
  • ISO 137:2015 Wool—Determination of fibre diameter—Projection microscope method
  • ISO 139:2005 Textiles—Standard atmospheres for conditioning and testing
  • ISO 140 Acoustics—Measurement of sound insulation in buildings and of building elements
    • ISO 140-2:1991 Part 2: Determination, verification and application of precision data [Withdrawn: replaced by ISO 12999-1:2014]
    • ISO 140-4:1998 Part 4: Field measurements of airborne sound insulation between rooms [Withdrawn: replaced by ISO 16283-1:2014]
    • ISO 140-5:1998 Part 5: Field measurements of airborne sound insulation of façade elements and façades [Withdrawn: replaced by ISO 16283-1:2014]
    • ISO 140-7:1998 Part 7: Field measurements of impact sound insulation of floors [Withdrawn: replaced by ISO 16283-1:2014]
    • ISO 140-14:2004 Part 14: Guidelines for special situations in the field [Withdrawn: replaced by ISO 16283-1:2014]
      • ISO 140-14:2004/Cor 1:2007
    • ISO 140-18:2006 Part 18: Laboratory measurement of sound generated by rainfall on building elements [Withdrawn: replaced by ISO 10140-1:2016]
  • ISO 141:1976 Textile machinery and accessories—Pirn winders and cross winders—Definition of left and right sides
  • ISO 142:1976 Textile machinery and accessories—Weaving preparatory machines—Definition of left and right sides
  • ISO 143:1977 Textile machinery and accessories—Weft pirns for automatic looms [Withdrawn without replacement]
  • ISO 144:1973 Steel—Reverse bend testing of wire [Withdrawn: replaced with ISO 7801]
  • ISO 146:1984 Metallic materials—Hardness test—Verification of Vickers hardness testing machines HV 0,2 to HV 100 [Withdrawn replaced with ISO 6507-2]
    • ISO 146-2:1993 Metallic materials—Verification of Vickers hardness testing machines—Part 2: Less than HV 0,2 [Withdrawn replaced with ISO 6507-2]
  • ISO 148 Metallic materials—Charpy pendulum impact test
    • ISO 148-1:2016 Part 1: Test method
    • ISO 148-2:2016 Part 2: Verification of testing machines
    • ISO 148-3:2016 Part 3: Preparation and characterization of Charpy V-notch test pieces for indirect verification of pendulum impact machines
  • ISO 150:2006 Raw, refined and boiled linseed oil for paints and varnishes—Specifications and methods of test
  • ISO 155:1998 Belt drives—Pulleys—Limiting values for adjustment of centres
  • ISO 156:1982 Metallic materials—Hardness test—Verification of Brinell hardness testing machines [Withdrawn replaced by ISO 6506-2]
  • ISO 157:1996 Coal—Determination of forms of sulfur
  • ISO 160:1980 Asbestos-cement pressure pipes and joints [Withdrawn without replacement]
  • ISO 161 Thermoplastics pipes for the conveyance of fluids—Nominal outside diameters and nominal pressures
    • ISO 161-1:1996 Part 1: Metric series
    • ISO 161-2:1996 Part 2: Inch-based series
  • ISO 162:1985 Cinematography—Head gaps and sound records for three-, four-, or six-track magnetic sound records on 35 mm and single-track on 17,5 mm motion-picture film containing no picture—Positions and width dimensions
  • ISO 171:1980 Plastics—Determination of bulk factor of moulding materials
  • ISO 172:1978 Plastics—Phenol-formaldehyde mouldings—Detection of free ammonia
  • ISO 174:1974 Plastics—Homopolymer and copolymer resins of vinyl chloride—Determination of viscosity number in dilute solution [Withdrawn replaced by ISO 1628-2]
  • ISO 175:2010 Plastics—Methods of test for the determination of the effects of immersion in liquid chemicals
  • ISO 176:2005 Plastics—Determination of loss of plasticizers—Activated carbon method
  • ISO 177:2016 Plastics—Determination of migration of plasticizers
  • ISO 178:2010 Plastics—Determination of flexural properties
  • ISO 179 Plastics—Determination of Charpy impact properties
    • ISO 179-1:2010 Part 1: Non-instrumented impact test
    • ISO 179-2:1997 Part 2: Instrumented impact test
  • ISO 180:2000 Plastics—Determination of Izod impact strength
  • ISO 182 Plastics—Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures
    • ISO 182-1:1990 Part 1: Congo red method
    • ISO 182-2:1990 Part 2: pH method
    • ISO 182-3:1993 Part 3: Conductometric method
    • ISO 182-4:1993 Part 4: Potentiometric method
  • ISO 185:2005 Grey cast irons - Classification
  • ISO 186:2002 Paper and board - Sampling to determine average quality
  • ISO 187:1990 Paper, board and pulps - Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples
  • ISO 188:2011 Rubber, vulcanized or thermoplastic - Accelerated ageing and heat resistance tests
  • ISO 196:1978 Wrought copper and copper alloys - Detection of residual stress - Mercury(I) nitrate test
  • ISO 197 Copper and copper alloys - Terms and definitions
    • ISO 197-1:1983 Part 1: Materials
    • ISO 197-2:1983 Part 2: Unwrought products (Refinery shapes)
    • ISO 197-3:1983 Part 3: Wrought products
    • ISO 197-4:1983 Part 4: Castings
    • ISO 197-5:1980 Part 5: Methods of processing and treatment
  • ISO 199:2014 Rolling bearings - Thrust bearings - Geometrical product specification (GPS) and tolerance values

ISO 200 – ISO 999

  • ISO 204:2009 Metallic materials - Uniaxial creep testing in tension - Method of test
  • ISO 209:2007 Aluminium and aluminium alloys - Chemical composition
  • ISO/TS 211:2014 Essential oils - General rules for labelling and marking of containers
  • ISO 212:2007 Essential oils - Sampling
  • ISO 214:1976 Documentation - Abstracts for publications and documentation
  • ISO 215:1986 Documentation - Presentation of contributions to periodicals and other serials
  • ISO 216:2007 Writing paper and certain classes of printed matter – Trimmed sizes – A and B series, and indication of machine direction
  • ISO 217:2013 Paper - Untrimmed sizes - Designation and tolerances for primary and supplementary ranges, and indication of machine direction
  • ISO 225:2010 Fasteners - Bolts, screws, studs and nuts - Symbols and descriptions of dimensions
  • ISO 226:2003 Acoustics – Normal equal-loudness-level contours
  • ISO 228 Pipe threads where pressure-tight joints are not made on the threads
  • ISO 229:1973 Machine tools - Speeds and feeds
  • ISO 230 Test code for machine tools
    • ISO 230-1:2012 Part 1: Geometric accuracy of machines operating under no-load or quasi-static conditions
    • ISO 230-2:2014 Part 2: Determination of accuracy and repeatability of positioning of numerically controlled axes
    • ISO 230-3:2007 Part 3: Determination of thermal effects
    • ISO 230-4:2005 Part 4: Circular tests for numerically controlled machine tools
    • ISO 230-5:2000 Part 5: Determination of the noise emission
    • ISO 230-6:2002 Part 6: Determination of positioning accuracy on body and face diagonals (Diagonal displacement tests)
    • ISO 230-7:2015 Part 7: Geometric accuracy of axes of rotation
    • ISO/TR 230-8:2010 Part 8: Vibrations
    • ISO/TR 230-9:2005 Part 9: Estimation of measurement uncertainty for machine tool tests according to series ISO 230, basic equations
    • ISO 230-10:2016 Part 10: Determination of the measuring performance of probing systems of numerically controlled machine tools
  • ISO 233 Information and documentation – Transliteration of Arabic characters into Latin characters[Note 3]
  • ISO 234 Files and rasps
    • ISO 234-1:1983 Part 1: Dimensions
    • ISO 234-2:1982 Part 2: Characteristics of cut
  • ISO 235:2016 Parallel shank jobber and stub series drills and Morse taper shank drills
  • ISO 236 Reamers[Note 3]
    • ISO 236-1:1976 Hand reamers
    • ISO 236-2:2013 Part 2: Long fluted machine reamers with Morse taper shanks
  • ISO 237:1975 Rotating tools with parallel shanks - Diameters of shanks and sizes of driving squares
  • ISO 238:2016 Reduction sleeves and extension sockets for tools with Morse taper shanks
  • ISO 239:1999 Drill chuck tapers
  • ISO 240:2016 Milling cutters - Interchangeability dimensions for cutter arbors or cutter mandrels
  • ISO 241:1994 Shanks for turning and planing tools - Shapes and dimensions of the section
  • ISO 242:2014 Carbide tips for brazing on turning tools
  • ISO 243:2014 Turning tools with carbide tips - External tools
  • ISO 244:1979 Aircraft - Sealing wire
  • ISO 245:1998 Aerospace - Lockwire - Diameters
  • ISO 246:2007 Rolling bearings - Cylindrical roller bearings, separate thrust collars - Boundary dimensions
  • ISO 247:2006 Rubber - Determination of ash
  • ISO 248 Rubber, raw - Determination of volatile-matter content
    • ISO 248-1:2011 Part 1: Hot-mill method and oven method
    • ISO 248-2:2012 Part 2: Thermogravimetric methods using an automatic analyser with an infrared drying unit
  • ISO 249:2016 Rubber, raw natural - Determination of dirt content
  • ISO 251:2012 Conveyor belts with textile carcass - Widths and lengths
  • ISO 252:2007 Conveyor belts - Adhesion between constitutive elements - Test methods
  • ISO 254:2011 Belt drives - Pulleys - Quality, finish and balance
  • ISO 255:1990 Belt drives - Pulleys for V-belts (system based on datum width) - Geometrical inspection of grooves
  • ISO 257:2004 Pesticides and other agrochemicals - Principles for the selection of common names
  • ISO 259 Information and documentation – Transliteration of Hebrew characters into Latin characters[Note 3]
  • ISO 261:1998 ISO general purpose metric screw threads – General plan
  • ISO 262:1998 ISO general purpose metric screw threads – Selected sizes for screws, bolts and nuts
  • ISO 263:1973 ISO inch screw threads - General plan and selection for screws, bolts and nuts - Diameter range 0,06 to 6 in
  • ISO 265 Pipes and fittings of plastics materials - Fittings for domestic and industrial waste pipes - Basic dimensions: Metric series
    • ISO 265-1:1988 Part 1: Unplasticized poly(vinyl chloride) (PVC-U)
  • ISO 266:1997 Acoustics - Preferred frequencies
  • ISO 268:1980 Aircraft - Mechanical and electromechanical indicators - General requirements
  • ISO 269:1985 Correspondence envelopes - Designation and sizes [Withdrawn without replacement]
  • ISO 272:1982 Fasteners - Hexagon products - Widths across flats
  • ISO 273:1979 Fasteners - Clearance holes for bolts and screws
  • ISO 276:2002 Binders for paints and varnishes - Linseed stand oil - Requirements and methods of test
  • ISO 277:2002 Binders for paints and varnishes - Raw tung oil - Requirements and methods of test
  • ISO 279:1998 Essential oils - Determination of relative density at 20 degrees C - Reference method
  • ISO 280:1998 Essential oils - Determination of refractive index
  • ISO 281:2007 Rolling bearings - Dynamic load ratings and rating life
  • ISO 282:1992 Conveyor belts - Sampling
  • ISO 283:2015 Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method
  • ISO 284:2012 Conveyor belts - Electrical conductivity - Specification and test method
  • ISO 286 Geometrical product specifications (GPS) – ISO code system for tolerances on linear sizes
    • ISO 286-1:2010 Part 1: Basis of tolerances, deviations and fits
    • ISO 286-2:2010 Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
  • ISO 287:2009 Paper and board - Determination of moisture content of a lot - Oven-drying method
  • ISO 289 Rubber, unvulcanized - Determinations using a shearing-disc viscometer
    • ISO 289-1:2015 Part 1: Determination of Mooney viscosity
    • ISO 289-2:2016 Part 2: Determination of pre-vulcanization characteristics
    • ISO 289-3:2015 Part 3: Determination of the Delta Mooney value for non-pigmented, oil-extended emulsion-polymerized SBR
    • ISO 289-4:2003 Part 4: Determination of the Mooney stress-relaxation rate
  • ISO 291:2008 Plastics - Standard atmospheres for conditioning and testing
  • ISO 293:2004 Plastics - Compression moulding of test specimens of thermoplastic materials
  • ISO 294 Plastics - Injection moulding of test specimens of thermoplastic materials
    • ISO 294-1:2017 Part 1: General principles, and moulding of multipurpose and bar test specimens
    • ISO 294-2:1996 Part 2: Small tensile bars
    • ISO 294-3:2002 Part 3: Small plates
    • ISO 294-4:2001 Part 4: Determination of moulding shrinkage
    • ISO 294-5:2011 Part 5: Preparation of standard specimens for investigating anisotropy
  • ISO 295:2004 Plastics - Compression moulding of test specimens of thermosetting materials
  • ISO 296:1991 Machine tools - Self-holding tapers for tool shanks
  • ISO 297:1988 7/24 tapers for tool shanks for manual changing
  • ISO 298:1973 Machine tools - Lathe centres - Sizes for interchangeability
  • ISO 299:1987 Machine tool tables - T-slots and corresponding bolts
  • ISO 302:2015 Pulps - Determination of Kappa number
  • ISO 306:2013 Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST)
  • ISO 361:1975 Basic ionizing radiation symbol
  • ISO 362 Measurement of noise emitted by accelerating road vehicles – Engineering method
    • ISO 362-1:2015 Part 1: M and N categories
    • ISO 362-2:2009 Part 2: L category
    • ISO 362-3:2016 Part 3: Indoor testing M and N categories
  • ISO 369:2009 Machine tools - Symbols for indications appearing on machine tools
  • ISO 374 Protective gloves against dangerous chemicals and micro-organisms
    • ISO 374-1:2016 Part 1: Terminology and performance requirements for chemical risks
    • ISO 374-5:2016 Part 5: Terminology and performance requirements for micro-organisms risks
  • ISO 384:2015 Laboratory glass and plastics ware – Principles of design and construction of volumetric instruments
  • ISO 385:2005 Laboratory glassware – Burettes
  • ISO 386:1977 Liquid-in-glass laboratory thermometers – Principles of design, construction and use
  • ISO 387:1977 Hydrometers – Principles of construction and adjustment
  • ISO 407:2004 Small medical gas cylinders – Pin-index yoke-type valve connections
  • ISO 428:1983 Wrought copper-aluminium alloys - Chemical composition and forms of wrought products [Withdrawn without replacement]
  • ISO 445:2013 Pallets for materials handling – Vocabulary
  • ISO 463:2006 Geometrical Product Specifications (GPS) – Dimensional measuring equipment – Design and metrological characteristics of mechanical dial gauges
  • ISO 472:2013 Plastics – Vocabulary
  • ISO 476:1982 Textile machinery and accessories – Pirn winding machines – Vocabulary
  • ISO 477:1982 Textile machinery and accessories – Cone and cheese winding machines – Vocabulary
  • ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
  • ISO 500 Agricultural tractors – Rear-mounted power take-off types 1, 2 and 3
  • ISO 518:2006 Photography – Camera accessory shoes, with and without electrical contacts, for photoflash lamps and electronic photoflash units – Specification
  • ISO 519:1992 Photography – Hand-held cameras – Flash-connector dimensions
  • ISO 532 Acoustics – Methods for calculating loudness
    • ISO 532-1:2017 Part 1: Zwicker method
    • ISO 532-2:2017 Part 2: Moore-Glasberg method
  • ISO 536:2012 Paper and board – Determination of grammage
  • ISO 561:1989 Coal preparation plant - Graphical symbols
  • ISO/TR 581:2005 Weldability - Metallic materials - General principles
  • ISO 611:2003 Road vehicles – Braking of automotive vehicles and their trailers – Vocabulary
  • ISO 612:1978 Road vehicles – Dimensions of motor vehicles and towed vehicles – Terms and definitions
  • ISO 633:2007 Cork – Vocabulary
  • ISO 639 Codes for the representation of names of languages
    • ISO 639-1:2002 Part 1: Alpha-2 code
    • ISO 639-2:1998 Part 2: Alpha-3 code
    • ISO 639-3:2007 Part 3: Alpha-3 code for comprehensive coverage of languages
    • ISO 639-4:2010 Part 4: General principles of coding of the representation of names of languages and related entities, and application guidelines
    • ISO 639-5:2008 Part 5: Alpha-3 code for language families and groups
    • ISO 639-6:2009 Part 6: Alpha-4 code for comprehensive coverage of language variants [Withdrawn, no replacement]
  • ISO/IEC 646:1991 Information technology – ISO 7-bit coded character set for information interchange
  • ISO 648:2008 Laboratory glassware – Single-volume pipettes
  • ISO 649 Laboratory glassware – Density hydrometers for general purposes
    • ISO 649-1:1981 Part 1: Specification
    • ISO 649-2:1981 Part 2: Test methods and use
  • ISO 650:1977 Relative density 60/60 degrees F hydrometers for general purposes
  • ISO 651:1975 Solid-stem calorimeter thermometers
  • ISO 652:1975 Enclosed-scale calorimeter thermometers
  • ISO 653:1980 Long solid-stem thermometers for precision use
  • ISO 654:1980 Short solid-stem thermometers for precision use
  • ISO 655:1980 Long enclosed-scale thermometers for precision use
  • ISO 656:1980 Short enclosed-scale thermometers for precision use
  • ISO 657 Hot-rolled steel sections
  • ISO 663:2017 Animal and vegetable fats and oils - Determination of insoluble impurities content
  • ISO 668 Series 1 freight containers – Classification, dimensions and ratings
  • ISO 676:1995 Spices and condiments – Botanical nomenclature
  • ISO 690:2010 Information and documentation – Guidelines for bibliographic references and citations to information resources
  • ISO 701:1998 International gear notation - Symbols for geometrical data
  • ISO 704:2009 Terminology work – Principles and methods
  • ISO 710 Graphical symbols for use on detailed maps, plans and geological cross-sections
    • ISO 710-1:1974 Part 1: General rules of representation
    • ISO 710-2:1974 Part 2: Representation of sedimentary rocks
    • ISO 710-3:1974 Part 3: Representation of magmatic rocks
    • ISO 710-4:1982 Part 4: Representation of metamorphic rocks
    • ISO 710-5:1989 Part 5: Representation of minerals
    • ISO 710-6:1984 Part 6: Representation of contact rocks and rocks which have undergone metasomatic, pneumatolytic or hydrothermal transformation or transformation by weathering
    • ISO 710-7:1984 Part 7: Tectonic symbols
  • ISO 732 Photography – 120-size and 220-size films – Dimensions
  • ISO 748:2007 Hydrometry – Measurement of liquid flow in open channels using current-meters or floats
  • ISO 760:1978 Determination of water - Karl Fischer method (General method)
  • ISO 764 Horology – Magnetic resistant watches
  • ISO 772:2011 Hydrometry - Vocabulary and symbols
  • ISO 780:2015 Packaging - Distribution packaging - Graphical symbols for handling and storage of packages
  • ISO 787 General methods of test for pigments and extenders
    • ISO 787-9:1981 Determination of pH value of an aqueous suspension
  • ISO 830:1999 Freight containers – Vocabulary
  • ISO 832:1994 Information and documentation - Bibliographic description and references - Rules for the abbreviation of bibliographic terms
  • ISO 835:2007 Laboratory glassware – Graduated pipettes
  • ISO 836:2001 Terminology for refractories
  • ISO 838:1974 Paper – Holes for general filing purposes – Specifications
  • ISO 843:1997 Information and documentation – Conversion of Greek characters into Latin characters
  • ISO 846:1997 Plastics – Evaluation of the action of microorganisms
  • ISO 857 Welding and allied processes - Vocabulary
    • ISO 857-2:2005 Part 2: Soldering and brazing processes and related terms
  • ISO 860:2007 Terminology work – Harmonization of concepts and terms
  • ISO 862:1984 Surface active agents – Vocabulary
  • ISO 898 Mechanical properties of fasteners made of carbon steel and alloy steel[Note 3]
  • ISO 928 Spices and condiments - Determination of total ash
  • ISO 936 Meat and meat products - Determination of total ash
  • ISO 962:1974 Information processing - Implementation of the 7- bit coded character set and its 7- bit and 8-bit extensions on 9- track 12,7 mm (0.5 in) magnetic tape
  • ISO 965 ISO general purpose metric screw threads – Tolerances
  • ISO 999:1996 Information and documentation – Guidelines for the content, organization, and presentation of indexes

ISO 1000 – ISO 4999

  • ISO 1000 SI units and recommendations for the use of their multiples and of certain other units [withdrawn 2009-11-17]
  • ISO/IEC 1001:2012 Information technology – File structure and labelling of magnetic tapes for information interchange
  • ISO 1004 Information processing – Magnetic ink character recognition – Print specifications
    • ISO 1004-1:2013 Part 1: Print specifications for E13B
    • ISO 1004-2:2013 Part 2: Print specifications for CMC7
  • ISO 1007 Photography – 135-size film and magazine – Specifications
  • ISO 1031:1974 Coniferous sawn timber – Defects – Terms and definitions
  • ISO 1032:1974 Coniferous sawn timber – Sizes – Terms and definitions
  • ISO 1034:1973 Aircraft - Ground air-conditioning connections
  • ISO 1042:1998 Laboratory glassware – One-mark volumetric flasks
  • ISO 1069:1973 Magnetic compasses and binnacles for sea navigation – Vocabulary
  • ISO 1070:1992 Liquid flow measurement in open channels – Slope-area method
  • ISO 1073 Alphanumeric character sets for optical recognition
    • ISO 1073-1:1976 Part 1: Character set OCR-A - Shapes and dimensions of the printed image
    • ISO 1073-2:1976 Part 2: Character set OCR-B - Shapes and dimensions of the printed image
  • ISO 1081:2013 Belt drives - V-belts and V-ribbed belts, and corresponding grooved pulleys - Vocabulary
  • ISO 1086:1991 Information and documentation – Title leaves of books
  • ISO 1087 Terminology work - Vocabulary
    • ISO 1087-1:2000 Part 1: Theory and application
  • ISO 1088:2007 Hydrometry – Velocity-area methods using current-meters – Collection and processing of data for determination of uncertainties in flow measurement
  • ISO 1101:2017 Geometrical product specifications (GPS) – Geometrical tolerancing – Tolerances of form, orientation, location and run-out
  • ISO 1100 Hydrometry – Measurement of liquid flow in open channels
    • ISO 1100-2:2010 Part 2: Determination of the stage-discharge relationship
  • ISO 1107:2017 Fishing nets – Netting – Basic terms and definitions
  • ISO 1112:2009 Horology – Functional and non-functional jewels
  • ISO 1113:1979 Information processing - Representation of the 7- bit coded character set on punched tape
  • ISO 1119:2011 Geometrical product specifications (GPS) - Series of conical tapers and taper angles
  • ISO 1122 Vocabulary of gear terms
    • ISO 1122-1:1998 Part 1: Definitions related to geometry
    • ISO 1122-2:1999 Part 2: Definitions related to worm gear geometry
  • ISO 1132 Rolling bearings - Tolerances
    • ISO 1132-1:2000 Part 1: Terms and definitions
  • ISO 1135 Transfusion equipment for medical use
    • ISO 1135-3:2016 Part 3: Blood-taking sets for single use
    • ISO 1135-4:2015 Part 4: Transfusion sets for single use, gravity feed
    • ISO 1135-5:2015 Part 5: Transfusion sets for single use with pressure infusion apparatus
  • ISO 1146:1988 Pyrometric reference cones for laboratory use – Specification
  • ISO 1151 Flight dynamics - Concepts, quantities and symbols
    • ISO 1151-1:1988 Part 1: Aircraft motion relative to the air
    • ISO 1151-2:1985 Part 2: Motions of the aircraft and the atmosphere relative to the Earth
    • ISO 1151-3:1989 Part 3: Derivatives of forces, moments and their coefficients
    • ISO 1151-4:1994 Part 4: Concepts and quantities used in the study of aircraft stability and control
    • ISO 1151-5:1987 Part 5: Quantities used in measurements
    • ISO 1151-6:1982 Part 6: Aircraft geometry
    • ISO 1151-7:1985 Part 7: Flight points and flight envelopes
    • ISO 1151-8:1992 Part 8: Concepts and quantities used in the study of the dynamic behaviour of the aircraft
    • ISO 1151-9:1993 Part 9: Models of atmospheric motions along the trajectory of the aircraft
  • ISO 1154:1975 Information processing – Punched paper tape – Dimensions and location of feed holes and code holes
  • ISO 1155:1978 Information processing – Use of longitudinal parity to detect errors in information messages
  • ISO 1176:1990 Road vehicles – Masses – Vocabulary and codes
  • ISO 1177:1985 Information processing – Character structure for start/stop and synchronous character oriented transmission
  • ISO 1182 Reaction to fire tests for products—Non-combustibility test
  • ISO 1213 Solid mineral fuels – Vocabulary
    • ISO 1213-1:1993 Part 1: Terms relating to coal preparation
    • ISO 1213-2:2016 Part 2: Terms relating to sampling, testing and analysis
  • ISO 1217 Displacement compressors—Acceptance tests
  • ISO 1219 Fluid power systems and components - Graphical symbols and circuit diagrams
    • ISO 1219-1:2012 Part 1: Graphical symbols for conventional use and data-processing applications
    • ISO 1219-2:2012 Part 2: Circuit diagrams
    • ISO 1219-3:2016 Part 3: Symbol modules and connected symbols in circuit diagrams
  • ISO 1222 Photography – Tripod connections
  • ISO 1268 Fibre-reinforced plastics – Methods of producing test plates
  • ISO 1302:2002 Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation
  • ISO 1382:2012 Rubber – Vocabulary
  • ISO 1402 Rubber and plastics hoses and hose assemblies - Hydrostatic testing
  • ISO 1413:2016 Horology - Shock-resistant wrist watches
  • ISO 1438:2017 Hydrometry – Open channel flow measurement using thin-plate weirs
  • ISO 1502:1996 ISO general-purpose metric screw threads – Gauges and gauging
  • ISO 1506:1982 Textile machinery – Dyeing, finishing and allied machinery – Classification and nomenclature
  • ISO 1531:1973 Fishing nets – Hanging of netting – Basic terms and definitions
  • ISO 1538:1984 Programming languages - ALGOL 60
  • ISO/IEC 1539 Information technology – Programming languages – Fortran
    • ISO/IEC 1539-1:2018 Part 1: Base language
    • ISO/IEC 1539-2:2000 Part 2: Varying length character strings
  • ISO 1586:1977 Textile machinery and accessories – Shuttles – Terms and designation in relation to the position of the shuttle eye
  • ISO 1629:2013 Rubber and latices – Nomenclature
  • ISO 1660:2017 Geometrical product specifications (GPS) - Geometrical tolerancing - Profile tolerancing
  • ISO 1663 Rigid cellular plastics – Determination of water vapour transmission properties
  • ISO 1680:2013 Acoustics – Test code for the measurement of airborne noise emitted by rotating electrical machines
  • ISO 1681:1973 Information processing – Unpunched paper cards – Specification
  • ISO 1683:2015 Acoustics - Preferred reference values for acoustical and vibratory levels
  • ISO 1703:2005 Assembly tools for screws and nuts - Designation and nomenclature
  • ISO 1730:1980 Dictation equipment – Basic operating requirements
  • ISO 1745:1975 Information processing – Basic mode control procedures for data communication systems
  • ISO 1750 Pesticides and other agrochemicals – Common names
  • ISO 1768:1975 Glass hydrometers – Conventional value for the thermal cubic expansion coefficient (for use in the preparation of measurement tables for liquids)
  • ISO 1769:1975 Laboratory glassware – Pipettes – Colour coding
  • ISO 1770:1981 Solid-stem general purpose thermometers
  • ISO 1771:1981 Enclosed-scale general purpose thermometers
  • ISO 1791:1983 Building construction – Modular co-ordination – Vocabulary
  • ISO 1803:1997 Building construction – Tolerances – Expression of dimensional accuracy – Principles and terminology
  • ISO 1804:1972 Doors – Terminology
  • ISO 1809:1977 Textile machinery and accessories – Types of formers for yarn packages – Nomenclature
  • ISO 1828:2012 Health informatics – Categorial structure for terminological systems of surgical procedures
  • ISO 1837:2003 Lifting hooks – Nomenclature
  • ISO 1858:1977 Information processing – General purpose hubs and reels, with 76 mm (3 in) centrehole, for magnetic tape used in interchange instrumentation applications
  • ISO 1859:1973 Information processing – Unrecorded magnetic tapes for interchange instrumentation applications – General dimensional requirements
  • ISO 1860:1986 Information processing – Precision reels for magnetic tape used in interchange instrumentation applications
  • ISO 1861:1975 Information processing – 7- track, 12,7 mm (0.5 in) wide magnetic tape for information interchange recorded at 8 rpmm (200 rpi)
  • ISO 1862:1975 Information processing – 9- track, 12,7 mm (0.5 in) wide magnetic tape for information interchange recorded at 8 rpmm (200 rpi)
  • ISO/IEC 1863:1990 Information processing – 9-track, 12,7 mm (0,5 in) wide magnetic tape for information interchange using NRZ1 at 32 ftpmm (800 ftpi) – 32 cpmm (800 cpi)
  • ISO/IEC 1864:1992 Information technology – Unrecorded 12,7 mm (0,5 in) wide magnetic tape for information interchange – 32 ftpmm (800 ftpi), NRZ1, 126 ftpmm (3 200 ftpi) phase encoded and 356 ftpmm (9 042 ftpi), NRZ1
  • ISO 1891:2009 Fasteners - Terminology
    • ISO 1891-2:2014 Part 2: Vocabulary and definitions for coatings
  • ISO 1928 Solid mineral fuels – Determination of gross calorific value by the bomb calorimetric method and calculation of net calorific value
  • ISO 1938 Geometrical product specifications (GPS) – Dimensional measuring equipment
    • ISO 1938-1:2015 Part 1: Plain limit gauges of linear size
    • ISO 1938-2:2017 Part 2: Reference disk gauges
  • ISO 1942:2009 Dentistry - Vocabulary
  • ISO 1951:2007 Presentation/representation of entries in dictionaries - Requirements, recommendations and information
  • ISO 1956 Fruits and vegetables – Morphological and structural terminology
    • ISO 1956-1:1982 (No part title)
    • ISO 1956-2:1989 (No part title)
  • ISO 1964:1987 Shipbuilding - Indication of details on the general arrangement plans of ships
  • ISO 1968:2004 Fibre ropes and cordage – Vocabulary
  • ISO/IEC 1989:2014 Information technology - Programming languages, their environments and system software interfaces - Programming language COBOL
  • ISO 1990 Fruits – Nomenclature
    • ISO 1990-1:1982 First list
    • ISO 1990-2:1985 Second list
  • ISO 1991 Vegetables – Nomenclature
    • ISO 1991-1:1982 First list
    • ISO 1991-2:1995 Part 2: Second list
  • ISO 1996 Acoustics – Description, measurement and assessment of environmental noise
    • ISO 1996-1:2016 Part 1: Basic quantities and assessment procedures[3]
    • ISO 1996-2:2017 Part 2: Determination of sound pressure levels
  • ISO 1998 Petroleum industry – Terminology
    • ISO 1998-1:1998 Part 1: Raw materials and products
    • ISO 1998-2:1998 Part 2: Properties and tests
    • ISO 1998-3:1998 Part 3: Exploration and production
    • ISO 1998-4:1998 Part 4: Refining
    • ISO 1998-5:1998 Part 5: Transport, storage, distribution
    • ISO 1998-6:2000 Part 6: Measurement
    • ISO 1998-7:1998 Part 7: Miscellaneous terms
    • ISO 1998-99:2000 Part 99: General and index
  • ISO 1999:2013 Acoustics - Estimation of noise-induced hearing loss[4]
  • ISO 2014:1976 Writing of calendar dates in all-numeric form [Withdrawn: replaced by ISO 8601:1988]
  • ISO 2015:1976 Numbering of weeks [Withdrawn: replaced by ISO 8601:1988]
  • ISO 2017 Mechanical vibration and shock – Resilient mounting systems
    • ISO 2017-1:2005 Part 1: Technical information to be exchanged for the application of isolation systems
    • ISO 2017-2:2007 Part 2: Technical information to be exchanged for the application of vibration isolation associated with railway systems
    • ISO 2017-3:2015 Part 3: Technical information to be exchanged for application of vibration isolation to new buildings
  • ISO/IEC 2022:1994 Information technology – Character code structure and extension techniques
  • ISO 2033:1983 Information processing - Coding of machine readable characters (MICR and OCR)
  • ISO 2041:2009 Mechanical vibration, shock and condition monitoring - Vocabulary
  • ISO 2047:1975 Information processing - Graphical representations for the control characters of the 7- bit coded character set
  • ISO 2074:2007 Plywood – Vocabulary
  • ISO 2076:2013 Textiles – Man-made fibres – Generic names
  • ISO 2080:2008 Metallic and other inorganic coatings - Surface treatment, metallic and other inorganic coatings - Vocabulary
  • ISO 2108:2005 Information and documentation – International standard book number (ISBN)
  • ISO 2110:1989 Information technology – Data communication – 25-pole DTE/DCE interface connector and contact number assignments
  • ISO 2145:1978 Documentation – Numbering of divisions and subdivisions in written documents
  • ISO 2146:2010 Information and documentation - Registry services for libraries and related organizations
  • ISO 2148:1974 Continuous handling equipment – Nomenclature
  • ISO 2151:2004 Acoustics – Noise test code for compressors and vacuum pumps – Engineering method (Grade 2)
  • ISO 2162 Technical product documentation – Springs
    • ISO 2162-1:1993 Part 1: Simplified representation
    • ISO 2162-2:1993 Part 2: Presentation of data for cylindrical helical compression springs
  • ISO 2171 Cereals, pulses and by-products – Determination of ash yield by incineration
  • ISO 2186:2007 Fluid flow in closed conduits – Connections for pressure signal transmissions between primary and secondary elements
  • ISO 2187:1990 Spinning preparatory machinery, spinning and doubling (twisting) machinery – List of equivalent terms
  • ISO 2203:1973 Technical drawings – Conventional representation of gears
  • ISO 2205:1975 Textile machinery and accessories – Drafting arrangements for spinning machines – Terminology
  • ISO 2240:2003 Photography – Colour reversal camera films – Determination of ISO speed
  • ISO 2257:1980 Office machines and printing machines used for information processing – Widths of fabric printing ribbons on spools
  • ISO 2258:1976 Printing ribbons – Minimum markings to appear on containers
  • ISO 2281:1990 Horology - Water-resistant watches [Withdrawn: replaced by ISO 22810:2010]
  • ISO 2300:1973 Sawn timber of broadleaved species – Defects – Terms and definitions
  • ISO 2331:1974 Fork lift trucks – Hook-on type fork arms – Vocabulary
  • ISO/IEC 2375:2003 Information technology - Procedure for registration of escape sequences and coded character sets
  • ISO/IEC 2382:2015 Information technology - Vocabulary
    • ISO/IEC 2382-36:2013 Part 36: Learning, education and training
    • ISO/IEC 2382-37:2017 Part 37: Biometrics
  • ISO 2384:1977 Documentation – Presentation of translations
  • ISO 2395:1990 Test sieves and test sieving - Vocabulary
  • ISO 2425:2010 Hydrometry – Measurement of liquid flow in open channels under tidal conditions
  • ISO 2444:1988 Joints in building – Vocabulary
  • ISO 2532:1974 Steel wire ropes - Vocabulary
  • ISO 2533:1975 Standard Atmosphere
  • ISO 2537:2007 Hydrometry – Rotating-element current-meters
  • ISO 2538 Geometrical product specifications (GPS) - Wedges
    • ISO 2538-1:2014 Part 1: Series of angles and slopes
    • ISO 2538-2:2014 Part 2: Dimensioning and tolerancing
  • ISO 2553:2013 Welding and allied processes – Symbolic representation on drawings – Welded joints
  • ISO 2574:1994 Aircraft – Electrical cables – Identification marking
  • ISO 2575:2010 Road vehicles - Symbols for controls, indicators and tell-tales
  • ISO/IEC 2593:2000 Information technology – Telecommunications and information exchange between systems – 34-pole DTE/DCE interface connector mateability dimensions and contact number assignments
  • ISO 2602:1980 Statistical interpretation of test results - Estimation of the mean - Confidence interval
  • ISO 2628:1973 Basic mode control procedures – Complements
  • ISO 2629:1973 Basic mode control procedures – Conversational information message transfer
  • ISO 2669:1995 Environmental tests for aircraft equipment - Steady-state acceleration
  • ISO 2671:1982 Environmental tests for aircraft equipment - Part 3.4 : Acoustic vibration
  • ISO 2685:1998 Aircraft - Environmental test procedure for airborne equipment - Resistance to fire in designated fire zones
  • ISO 2692:2014 Geometrical product specifications (GPS) – Geometrical tolerancing – Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
  • ISO 2709:2008 Information and documentation – Format for information exchange
  • ISO 2710 Reciprocating internal combustion engines - Vocabulary
    • ISO 2710-1:2000 Part 1: Terms for engine design and operation
    • ISO 2710-2:1999 Part 2: Terms for engine maintenance
  • ISO 2711:1973 Information processing interchange - Representation of ordinal dates [Withdrawn: replaced by ISO 8601:1988]
  • ISO 2768 General tolerances
    • ISO 2768-1:1989 Part 1: Tolerances for linear and angular dimensions without individual tolerance indications
    • ISO 2768-2:1989 Part 2: Geometrical tolerances for features without individual tolerance indications
  • ISO 2775:1977 Office machines and printing machines used for information processing – Widths of one-time paper or plastic printing ribbons and marking to indicate the end of the ribbons
  • ISO 2784:1974 Continuous forms used for information processing - Sizes and sprocket feed holes
  • ISO 2788:1986 Documentation - Guidelines for the establishment and development of monolingual thesauri [Withdrawn: replaced by ISO 25964-1:2011]
  • ISO 2789:2013 Information and documentation - International library statistics
  • ISO 2806:1994 Industrial automation systems - Numerical control of machines - Vocabulary
  • ISO 2822 Raw cattle hides and calf skins
    • ISO 2822-1:1998 Part 1: Descriptions of defects
  • ISO 2848:1984 Building construction - Modular coordination - Principles and rules
  • ISO 2852 Stainless steel clamp pipe couplings for the food industry
  • ISO 2854:1976 Statistical interpretation of data - Techniques of estimation and tests relating to means and variances
  • ISO 2859 Sampling procedures for inspection by attributes
    • ISO 2859-1:1999 Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
    • ISO 2859-2:1985 Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection
    • ISO 2859-3:2005 Part 3: Skip-lot sampling procedures
    • ISO 2859-4:2002 Part 4: Procedures for assessment of declared quality levels
    • ISO 2859-5:2005 Part 5: System of sequential sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection
    • ISO 2859-10:2006 Part 10: Introduction to the ISO 2859 series of standards for sampling for inspection by attributes
  • ISO 2922:2000 Acoustics – Measurement of airborne sound emitted by vessels on inland waterways and harbours
  • ISO 2923:1996 Acoustics - Measurement of noise on board vessels
  • ISO 2954:2012 Mechanical vibration of rotating and reciprocating machinery – Requirements for instruments for measuring vibration severity
  • ISO 2972:1979 Numerical control of machines - Symbols
  • ISO 2975 Measurement of water flow in closed conduits – Tracer methods
    • ISO 2975-1:1974 Part 1: General
    • ISO 2975-2:1975 Part 2: Constant rate injection method using non-radioactive tracers
    • ISO 2975-3:1976 Part 3: Constant rate injection method using radioactive tracers
    • ISO 2975-6:1977 Part 6: Transit time method using non-radioactive tracers
    • ISO 2975-7:1977 Part 7: Transit time method using radioactive tracers
  • ISO 3002 Basic quantities in cutting and grinding
    • ISO 3002-1:1982 Part 1: Geometry of the active part of cutting tools – General terms, reference systems, tool and working angles, chip breakers
    • ISO 3002-2:1982 Part 2: Geometry of the active part of cutting tools – General conversion formulae to relate tool and working angles
    • ISO 3002-3:1984 Part 3: Geometric and kinematic quantities in cutting
    • ISO 3002-4:1984 Part 4: Forces, energy, power
    • ISO 3002-5:1989 Part 5: Basic terminology for grinding processes using grinding wheels
  • ISO 3029:1995 Photography - 126-size cartridges - Dimensions of cartridge, film and backing paper [Withdrawn without replacement]
  • ISO 3040:2016 Geometrical product specifications (GPS) – Dimensioning and tolerancing – Cones
  • ISO 3046 Reciprocating internal combustion engines – Performance
    • ISO 3046-5:2001 Part 5: Torsional vibrations
  • ISO 3082 Iron ores – Sampling and sample preparation procedures
  • ISO 3095:2013 Acoustics – Railway applications – Measurement of noise emitted by railbound vehicles
  • ISO 3098 Technical product documentation – Lettering
    • ISO 3098-1:2015 Part 1: General requirements
    • ISO 3098-2:2000 Part 2: Latin alphabet, numerals and marks
    • ISO 3098-3:2000 Part 3: Greek alphabet
    • ISO 3098-4:2000 Part 4: Diacritical and particular marks for the Latin alphabet
    • ISO 3098-5:1997 Part 5: CAD lettering of the Latin alphabet, numerals and marks
    • ISO 3098-6:2000 Part 6: Cyrillic alphabet
  • ISO 3103 Tea – Preparation of liquor for use in sensory tests
  • ISO 3105:1994 Glass capillary kinematic viscometers – Specifications and operating instructions
  • ISO 3166 Codes for the representation of names of countries and their subdivisions
    • ISO 3166-1:2013 Part 1: Country codes
    • ISO 3166-2:2013 Part 2: Country subdivision code
    • ISO 3166-3:2013 Part 3: Code for formerly used names of countries
  • ISO 3252:1999 Powder metallurgy – Vocabulary
  • ISO 3272 Microfilming of technical drawings and other drawing office documents
    • ISO 3272-1:2003 Part 1: Operating procedures
    • ISO 3272-2:1994 Part 2: Quality criteria and control of 35 mm silver gelatin microfilms
    • ISO 3272-3:2001 Part 3: Aperture card for 35 mm microfilm
    • ISO 3272-4:1994 Part 4: Microfilming of drawings of special and exceptional elongated sizes
    • ISO 3272-6:2000 Part 6: Quality criteria and control of systems for enlargements from 35 mm microfilm
  • ISO 3274:1996 Geometrical Product Specifications (GPS) – Surface texture: Profile method – Nominal characteristics of contact (stylus) instruments
  • ISO 3275:1974 Information processing - Implementation of the 7- bit coded character set and its 7- bit and 8- bit extensions on 3,81 mm magnetic cassette for data interchange
  • ISO 3287:1999 Powered industrial trucks - Symbols for operator controls and other displays
  • ISO 3297:2007 Information and documentation – International standard serial number (ISSN)
  • ISO 3301:1975 Statistical interpretation of data - Comparison of two means in the case of paired observations
  • ISO 3307:1975 Information interchange - Representations of time of the day [Withdrawn: replaced by ISO 8601:1988]
  • ISO 3354:2008 Measurement of clean water flow in closed conduits – Velocity-area method using current-meters in full conduits and under regular flow conditions
  • ISO 3381:2005 Railway applications – Acoustics – Measurement of noise inside railbound vehicles
  • ISO 3394:2012 Packaging - Complete, filled transport packages and unit loads - Dimensions of rigid rectangular packages
  • ISO 3407:1983 Information processing – Information interchange on 3,81 mm (0.150 in) magnetic tape cassette at 4 cpmm (100 cpi), phase encoded at 63 ftpmm (1 600 ftpi)
  • ISO 3408 Ball screws
    • ISO 3408-1:2006 Part 1: Vocabulary and designation
  • ISO 3454:2008 Hydrometry – Direct depth sounding and suspension equipment
  • ISO 3455:2007 Hydrometry – Calibration of current-meters in straight open tanks
  • ISO 3493:2014 Vanilla – Vocabulary
  • ISO 3494:1976 Statistical interpretation of data - Power of tests relating to means and variances
  • ISO 3506 Mechanical properties of corrosion-resistant stainless steel fasteners
  • ISO 3507:1999 Laboratory glassware – Pyknometers
  • ISO 3509:2005 Coffee and coffee products – Vocabulary
  • ISO 3511 Industrial process measurement control functions and instrumentation - Symbolic representation[Note 3]
    • ISO 3511-1:1977 Part 1: Basic requirements
    • ISO 3511-2:1984 Part 2: Extension of basic requirements
    • ISO 3511-3:1984 Part 3: Detailed symbols for instrument interconnection diagrams
    • ISO 3511-4:1985 Part 4: Basic symbols for process computer, interface, and shared display/control functions
  • ISO 3529 Vacuum technology - Vocabulary
    • ISO 3529-1:1981 Part 1: General terms
    • ISO 3529-2:1981 Part 2: Vacuum pumps and related terms
    • ISO 3529-3:2014 Part 3: Total and partial pressure vacuum gauges
  • ISO 3534 Statistics – Vocabulary and symbols
    • ISO 3534-1:2006 Part 1: General statistical terms and terms used in probability
    • ISO 3534-2:2006 Part 2: Applied statistics
    • ISO 3534-3:2013 Part 3: Design of experiments
    • ISO 3534-4:2014 Part 4: Survey sampling
  • ISO 3535:1977 Forms design sheet and layout chart
  • ISO 3536:2016 Road vehicles – Safety glazing materials – Vocabulary
  • ISO 3537 Road vehicles – Safety glazing materials – Mechanical tests
  • ISO 3538 Road vehicles – Safety glazing materials – Test methods for optical properties
  • ISO 3540:1976 Paper or plastic printing ribbons – Characteristics of cores
  • ISO 3561:1976 Information processing – Interchangeable magnetic six-disk pack – Track format
  • ISO 3562:1976 Information processing – Interchangeable magnetic single-disk cartridge (top loaded) – Physical and magnetic characteristics
  • ISO 3563:1976 Information processing – Interchangeable magnetic single-disk cartridge (top loaded) – Track format
  • ISO 3564:1976 Information processing – Interchangeable magnetic eleven-disk pack – Physical and magnetic characteristics
  • ISO 3572:1976 Textiles – Weaves – Definitions of general terms and basic weaves
  • ISO 3591 Sensory analysis – Apparatus – Wine-tasting glass
  • ISO 3593 Starch — Determination of ash
  • ISO 3601 Fluid power systems – O-rings
    • ISO 3601-1 Inside diameters, cross-sections, tolerances and designation codes
    • ISO 3601-2 Housing dimensions for general applications
    • ISO 3601-3 Quality acceptance criteria
    • ISO 3601-4 Anti-extrusion rings (back-up rings)
    • ISO 3601-5 Suitability of elastomeric materials for industrial applications
  • ISO 3602:1989 Documentation – Romanization of Japanese (kana script)
  • ISO 3611:2010 Geometrical product specifications (GPS) – Dimensional measuring equipment: Micrometers for external measurements – Design and metrological characteristics
  • ISO 3632 Spices – Saffron (Crocus sativus L.)[Note 3]
  • ISO 3635:1981 Size designation of clothes – Definitions and body measurement procedure
  • ISO 3650:1998 Geometrical Product Specifications (GPS) – Length standards – Gauge blocks
  • ISO 3660:1976 Fishing nets – Mounting and joining of netting – Terms and illustrations
  • ISO/TR 3666:1998 Viscosity of water
  • ISO 3676:2012 Packaging - Complete, filled transport packages and unit loads - Unit load dimensions
  • ISO 3690 Welding and allied processes — Determination of hydrogen content in arc weld metal
  • ISO 3692:1976 Information processing – Reels and cores for 25,4 mm (1 in) perforated paper tape for information interchange – Dimensions
  • ISO 3713:1987 Ferroalloys - Sampling and preparation of samples - General rules
  • ISO 3715 Ships and marine technology – Propulsion plants for ships
    • ISO 3715-1:2002 Part 1: Vocabulary for geometry of propellers
    • ISO 3715-2:2001 Part 2: Vocabulary for controllable-pitch propeller plants
  • ISO/TS 3716:2006 Hydrometry – Functional requirements and characteristics of suspended-sediment samplers
  • ISO 3740:2000 Acoustics – Determination of sound power levels of noise sources – Guidelines for the use of basic standards
  • ISO 3741:2010 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Precision methods for reverberation test rooms
  • ISO 3743 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering methods for small movable sources in reverberant fields[Note 3]
    • ISO 3743-1:2010 Part 1: Comparison method for a hard-walled test room
    • ISO 3743-2:1994 Part 2: Methods for special reverberation test rooms
  • ISO 3744:2010 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering methods for an essentially free field over a reflecting plane
  • ISO 3745:2012 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Precision methods for anechoic rooms and hemi-anechoic rooms
  • ISO 3746:2010 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Survey method using an enveloping measurement surface over a reflecting plane
  • ISO 3747:2010 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering/survey methods for use in situ in a reverberant environment
  • ISO 3766:2003 Construction drawings – Simplified representation of concrete reinforcement
  • ISO 3767 Tractors, machinery for agriculture and forestry, powered lawn and garden equipment - Symbols for operator controls and other displays
    • ISO 3767-1:2016 Part 1: Common symbols
    • ISO 3767-2:2016 Part 2: Symbols for agricultural tractors and machinery
    • ISO 3767-3:2016 Part 3: Symbols for powered lawn and garden equipment
    • ISO 3767-4:2016 Part 4: Symbols for forestry machinery
    • ISO 3767-5:2016 Part 5: Symbols for manual portable forestry machines
  • ISO/IEC 3788:1990 Information processing – 9-track, 12,7 mm (0,5 in) wide magnetic tape for information interchange using phase encoding at 126 ftpmm (3 200 ftpi), 63 cpmm (1 600 cpi)
  • ISO 3791:1976 Office machines and data processing equipment - Keyboard layouts for numeric applications
  • ISO 3792:1976 Adding machines - Layout of function keyboard
  • ISO 3802:1976 Information processing – General purpose reels with 8 mm (5/16 in) centre hole for magnetic tape for interchange instrumentation applications
  • ISO 3819:2015 Laboratory glassware – Beakers
  • ISO 3822 Acoustics – Laboratory tests on noise emission from appliances and equipment used in water supply installations
    • ISO 3822-1:1999 Part 1: Method of measurement
    • ISO 3822-2:1995 Part 2: Mounting and operating conditions for draw-off taps and mixing valves
    • ISO 3822-3:1997 Part 3: Mounting and operating conditions for in-line valves and appliances
    • ISO 3822-4:1997 Part 4: Mounting and operating conditions for special appliances
  • ISO 3826 Plastics collapsible containers for human blood and blood components
    • ISO 3826-1:2013 Part 1: Conventional containers
    • ISO 3826-2:2008 Part 2: Graphical symbols for use on labels and instruction leaflets
    • ISO 3826-3:2006 Part 3: Blood bag systems with integrated features
    • ISO 3826-4:2015 Part 4: Aphaeresis blood bag systems with integrated features
  • ISO 3828:2008 Shipbuilding and marine structures – Deck machinery – Vocabulary and symbols
  • ISO 3833:1977 Road vehicles – Types – Terms and definitions
  • ISO 3835 Equipment for vine cultivation and wine making – Vocabulary
    • ISO 3835-1:1976 (No part title)
    • ISO 3835-3:1980 (No part title)
    • ISO 3835-4:1981 (No part title)
  • ISO 3846:2008 Hydrometry – Open channel flow measurement using rectangular broad-crested weirs
  • ISO 3847:1977 Liquid flow measurement in open channels by weirs and flumes – End-depth method for estimation of flow in rectangular channels with a free overfall
  • ISO 3855:1977 Milling cutters - Nomenclature
  • ISO 3857 Compressors, pneumatic tools and machines - Vocabulary
    • ISO 3857-1:1977 Part 1: General
    • ISO 3857-2:1977 Part 2: Compressors
    • ISO 3857-3:1989 Part 3: Pneumatic tools and machines
    • ISO 3857-4:2012 Part 4: Air treatment
  • ISO 3861:2005 Rubber hoses for sand and grit blasting - Specification
  • ISO 3864 Graphical symbols – Safety colours and safety signs
  • ISO 3866:1977 Office machines and printing machines used for information processing – Widths of fabric printing ribbons on spools exceeding 19 mm
  • ISO 3877 Tyres, valves and tubes – List of equivalent terms
    • ISO 3877-1:1997 Part 1: Tyres
    • ISO 3877-2:1997 Part 2: Tyre valves
    • ISO 3877-3:1978 Part 3: Tubes
    • ISO 3877-4:1984 Part 4: Solid tyres
  • ISO 3880 Building construction – Stairs – Vocabulary
    • ISO 3880-1:1977
  • ISO 3883:1977 Office machines – Line and character capacity of address masters
  • ISO 3901:2001 Information and documentation – International Standard Recording Code (ISRC)
  • ISO 3911:2004 Wheels and rims for pneumatic tyres – Vocabulary, designation and marking
  • ISO 3918:2007 Milking machine installations – Vocabulary
  • ISO 3950:2016 Dentistry - Designation system for teeth and areas of the oral cavity
  • ISO 3951 Sampling procedures for inspection by variables
    • ISO 3951-1:2013 Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL
    • ISO 3951-2:2013 Part 2: General specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics
    • ISO 3951-3:2007 Part 3: Double sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
    • ISO 3951-4:2011 Part 4: Procedures for assessment of declared quality levels
    • ISO 3951-5:2006 Part 5: Sequential sampling plans indexed by acceptance quality limit (AQL) for inspection by variables (known standard deviation)
  • ISO 3952 Kinematic diagrams - Graphical symbols
    • ISO 3952-1:1981 (Motion of links of mechanisms; Kinematic pairs; Links and connections of their components; Linkage of bars and their links)
    • ISO 3952-2:1981 (Friction and gear mechanisms; Cam mechanisms)
    • ISO 3952-3:1979 (Maltese and ratchet mechanisms; Couplings and brakes)
    • ISO 3952-4:1984 (Miscellaneous mechanisms and their components)
  • ISO 3966:2008 Measurement of fluid flow in closed conduits – Velocity area method using Pitot static tubes
  • ISO 3977 Gas turbines – Procurement
  • ISO 4006:1991 Measurement of fluid flow in closed conduits - Vocabulary and symbols
  • ISO 4007:2012 Personal protective equipment - Eye and face protection - Vocabulary
  • ISO 4031:1978 Information interchange - Representation of local time differentials [Withdrawn: replaced by ISO 8601:1988]
  • ISO 4037 X and gamma reference radiation for calibrating dosemeters and doserate meters and for determining their response as a function of photon energy
    • ISO 4037-1:1996 Part 1: Radiation characteristics and production
    • ISO 4037-2:1997 Part 2: Dosimetry for radiation protection over the energy ranges from 8 keV to 1,3 MeV and 4 MeV to 9 MeV
    • ISO 4037-3:1999 Part 3: Calibration of area and personal dosemeters and the measurement of their response as a function of energy and angle of incidence
    • ISO 4037-4:2004 Part 4: Calibration of area and personal dosemeters in low energy X reference radiation fields
  • ISO 4046 Paper, board, pulps and related terms – Vocabulary
    • ISO 4046-1:2016 Part 1: Alphabetical index
    • ISO 4046-2:2016 Part 2: Pulping terminology
    • ISO 4046-3:2016 Part 3: Paper-making terminology
    • ISO 4046-4:2016 Part 4: Paper and board grades and converted products
    • ISO 4046-5:2016 Part 5: Properties of pulp, paper and board
  • ISO 4057:1986 Information processing – Data interchange on 6,30 mm (0.25 in) magnetic tape cartridge, 63 bpmm (1 600 bpi) phase-encoded
  • ISO 4063:2009 Welding and allied processes - Nomenclature of processes and reference numbers
  • ISO 4074 Natural latex rubber condoms – Requirements and test methods
  • ISO 4087:2005 Micrographics - Microfilming of newspapers for archival purposes on 35 mm microfilm
  • ISO 4125:1991 Dry fruits and dried fruits – Definitions and nomenclature
  • ISO 4129:2012 Road vehicles - Mopeds - Symbols for controls, indicators and tell-tales
  • ISO 4130:1978 Road vehicles – Three-dimensional reference system and fiducial marks – Definitions
  • ISO 4135:2001 Anaesthetic and respiratory equipment - Vocabulary
  • ISO 4139:1979 Ferrosilicon - Determination of aluminium content - Flame atomic absorption spectrometric method
  • ISO 4140:1979 Ferrochromium and ferrosilicochromium - Determination of chromium content - Potentiometric method
  • ISO 4157 Construction drawings – Designation systems
  • ISO 4158:1978 Ferrosilicon, ferrosilicomanganese and ferrosilicochromium - Determination of silicon content - Gravimetric method
  • ISO 4159:1978 Ferromanganese and ferrosilicomanganese - Determination of manganese content - Potentiometric method
  • ISO 4165 Road vehicles — Electrical connections — Double-pole connection
  • ISO 4172:1991 Technical drawings – Construction drawings – Drawings for the assembly of prefabricated structures
  • ISO 4173:1980 Ferromolybdenum - Determination of molybdenum content - Gravimetric method
  • ISO 4179 Ductile iron pipes and fittings for pressure and non-pressure pipelines – Cement mortar lining
  • ISO 4185:1980 Measurement of liquid flow in closed conduits – Weighing method
  • ISO 4217:2015 Codes for the representation of currencies
  • ISO 4223 Definitions of some terms used in the tyre industry
    • ISO 4223-1:2017 Part 1: Pneumatic tyres
    • ISO 4223-2:1991 Part 2: Solid tyres
  • ISO 4225:1994 Air quality - General aspects - Vocabulary
  • ISO 4226:2007 Air quality – General aspects – Units of measurement
  • ISO 4232 Office machines – Minimum information to be included in specification sheets
    • ISO 4232-3:1984 Part 3: Postal franking machines
  • ISO 4246:1994 Cinematography - Vocabulary
  • ISO 4248:1978 Jig bushes - Definitions and nomenclature
  • ISO 4287:1997 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Terms, definitions and surface texture parameters
  • ISO 4288:1996 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Rules and procedures for the assessment of surface texture
  • ISO 4291:1985 Methods for the assessement of departure from roundness - Measurement of variations in radius
  • ISO 4306 Cranes – Vocabulary
    • ISO 4306-1:2007 Part 1: General
    • ISO 4306-2:2012 Part 2: Mobile cranes
    • ISO 4306-3:2016 Part 3: Tower cranes
    • ISO 4306-5:2005 Part 5: Bridge and gantry cranes
  • ISO 4314 Surface active agents — Determination of free alkalinity or free acidity — Titrimetric method
  • ISO 4337:1977 Information processing – Interchangeable magnetic twelve-disk pack (100 Mbytes)
  • ISO 4341:1978 Information processing – Magnetic tape cassette and cartridge labelling and file structure for information interchange
  • ISO 4346:1977 Steel wire ropes for general purposes - Lubricants - Basic requirements
  • ISO 4359:2013 Flow measurement structures – Rectangular, trapezoidal and U-shaped flumes
  • ISO 4360:2008 Hydrometry – Open channel flow measurement using triangular profile weirs
  • ISO 4362:1999 Hydrometric determinations – Flow measurement in open channels using structures – Trapezoidal broad-crested weirs
  • ISO 4363:2002 Measurement of liquid flow in open channels – Methods for measurement of characteristics of suspended sediment
  • ISO 4364:1997 Measurement of liquid flow in open channels – Bed material sampling
  • ISO 4365:2005 Liquid flow in open channels – Sediment in streams and canals – Determination of concentration, particle size distribution and relative density
  • ISO 4366:2007 Hydrometry – Echo sounders for water depth measurements
  • ISO 4369:1979 Measurement of liquid flow in open channels – Moving-boat method
  • ISO 4371:1984 Measurement of liquid flow in open channels by weirs and flumes – End depth method for estimation of flow in non-rectangular channels with a free overfall (approximate method)
  • ISO 4373:2008 Hydrometry – Water level measuring devices
  • ISO 4374:1990 Liquid flow measurement in open channels – Round-nose horizontal broad-crested weirs
  • ISO 4375:2014 Hydrometry – Cableway systems for stream gauging
  • ISO 4377:2012 Hydrometric determinations – Flow measurement in open channels using structures – Flat-V weirs
  • ISO 4378 Plain bearings - Terms, definitions, classification and symbols
    • ISO 4378-1:2017 Part 1: Design, bearing materials and their properties
    • ISO 4378-2:2017 Part 2: Friction and wear
    • ISO 4378-3:2017 Part 3: Lubrication
    • ISO 4378-4:2009 Part 4: Basic symbols
    • ISO 4378-5:2009 Part 5: Application of symbols
    • ISO/TR 4378-6:2012 Part 6: Abbreviated terms
  • ISO 4412 Hydraulic fluid power – Test code for determination of airborne noise levels
    • ISO 4412-1:1991 Part 1: Pumps
    • ISO 4412-2:1991 Part 2: Motors
    • ISO 4412-3:1991 Part 3: Pumps – Method using a parallelepiped microphone array
  • ISO 4413:2010 Hydraulic fluid power – General rules and safety requirements for systems and their components
  • ISO 4481:1977 Cutlery and flatware – Nomenclature
  • ISO 4548 Methods of test for full-flow lubricating oil filters for internal combustion engines
    • ISO 4548-7:2012 Part 7: Vibration fatigue test
  • ISO 4551:1987 Ferroalloys - Sampling and sieve analysis
  • ISO 4552 Ferroalloys - Sampling and sample preparation for chemical analysis
  • ISO 4578 Adhesives — Determination of peel resistance of high-strength adhesive bonds — Floating-roller method
  • ISO 4582 Plastics — Determination of changes in colour and variations in properties after exposure to daylight under glass, natural weathering or laboratory light sources
  • ISO 4587 Adhesives — Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies
  • ISO 4618:2014 Paints and varnishes – Terms and definitions
  • ISO 4628 Paints and varnishes – Evaluation of degradation of coatings – Designation of quantity and size of defects, and of intensity of uniform changes in appearance
    • ISO 4628-1 General introduction and designation system
    • ISO 4628-2 Assessment of degree of blistering
    • ISO 4628-3 Assessment of degree of rusting
    • ISO 4628-4 Assessment of degree of cracking
    • ISO 4628-5 Assessment of degree of flaking
    • ISO 4628-6 Assessment of degree of chalking by tape method
    • ISO 4628-7 Assessment of degree of chalking by velvet method
    • ISO 4628-8 Assessment of degree of delamination and corrosion around a scribe
    • ISO 4628-10 Assessment of degree of filiform corrosion
  • ISO 4683 Raw sheep skins
    • ISO 4683-1:1998 Part 1: Descriptions of defects
  • ISO 4720:2009 Essential oils – Nomenclature
  • ISO 4730:2017 Essential oil of Melaleuca, terpinen-4-ol type (Tea Tree oil)
  • ISO 4786:1977 Enclosed-scale adjustable-range thermometers
  • ISO 4787:2010 Laboratory glassware – Volumetric instruments – Methods for testing of capacity and for use
  • ISO 4788:2005 Laboratory glassware – Graduated measuring cylinders
  • ISO 4791 Laboratory apparatus – Vocabulary relating to apparatus made essentially from glass, porcelain or vitreous silica
    • ISO 4791-1:1985 Part 1: Names for items of apparatus
  • ISO 4795:1996 Glass for thermometer bulbs
  • ISO 4801:1979 Glass alcoholometers and alcohol hydrometers not incorporating a thermometer
  • ISO 4805:1982 Laboratory glassware – Thermo-alcoholometers and alcohol-thermohydrometers
  • ISO 4831:2006 Microbiology of food and animal feeding stuffs – Horizontal method for the detection and enumeration of coliforms – Most probable number technique
  • ISO 4832:2006 Microbiology of food and animal feeding stuffs – Horizontal method for the enumeration of coliforms – Colony-count technique
  • ISO 4833 Microbiology of the food chain – Horizontal method for the enumeration of microorganisms
    • ISO 4833-1:2013 Part 1: Colony count at 30 degrees C by the pour plate technique
    • ISO 4833-2:2013 Part 2: Colony count at 30 degrees C by the surface plating technique
  • ISO 4866:2010 Mechanical vibration and shock – Vibration of fixed structures – Guidelines for the measurement of vibrations and evaluation of their effects on structures
  • ISO 4871:1996 Acoustics – Declaration and verification of noise emission values of machinery and equipment
  • ISO/IEC 4873:1991 Information technology – ISO 8-bit code for information interchange – Structure and rules for implementation
  • ISO 4875 Metal-cutting band saw blades
    • ISO 4875-1:2006 Part 1: Vocabulary
  • ISO 4880:1997 Burning behaviour of textiles and textile products - Vocabulary
  • ISO 4882:1979 Office machines and data processing equipment - Line spacings and character spacings
  • ISO 4885:2017 Ferrous materials - Heat treatments - Vocabulary
  • ISO 4892 Plastics – Methods of exposure to laboratory light sources
  • ISO 4902:1989 Information technology – Data communication – 37-pole DTE/DCE interface connector and contact number assignments
  • ISO 4903:1989 Information technology – Data communication – 15-pole DTE/DCE interface connector and contact number assignments
  • ISO/IEC 4909:2006 Identification cards - Financial transaction cards - Magnetic stripe data content for track 3
  • ISO 4921:2000 Knitting – Basic concepts – Vocabulary

Notes

  1. This list generally excludes draft versions.
  2. ISO deliverables include "specifications" (ISO/PAS, ISO/TS), "reports" (ISO/TR), etc, which are not referred to by ISO as "standards".
  3. The exact wording of this title varies between parts. This is the wording of the most recently published part.

References

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.