# Iterative method

In computational mathematics, an **iterative method** is a mathematical procedure that uses an initial guess to generate a sequence of improving approximate solutions for a class of problems, in which the *n*-th approximation is derived from the previous ones. A specific implementation of an iterative method, including the termination criteria, is an algorithm of the iterative method. An iterative method is called **convergent** if the corresponding sequence converges for given initial approximations. A mathematically rigorous convergence analysis of an iterative method is usually performed; however, heuristic-based iterative methods are also common.

In contrast, **direct methods** attempt to solve the problem by a finite sequence of operations. In the absence of rounding errors, direct methods would deliver an exact solution (like solving a linear system of equations by Gaussian elimination). Iterative methods are often the only choice for nonlinear equations. However, iterative methods are often useful even for linear problems involving many variables (sometimes of the order of millions), where direct methods would be prohibitively expensive (and in some cases impossible) even with the best available computing power.[1]

## Attractive fixed points

If an equation can be put into the form *f*(*x*) = *x*, and a solution **x** is an attractive fixed point of the function *f*, then one may begin with a point *x*_{1} in the basin of attraction of **x**, and let *x*_{n+1} = *f*(*x*_{n}) for *n* ≥ 1, and the sequence {*x*_{n}}_{n ≥ 1} will converge to the solution **x**. Here *x*_{n} is the *n*th approximation or iteration of *x* and *x*_{n+1} is the next or *n* + 1 iteration of *x*. Alternately, superscripts in parentheses are often used in numerical methods, so as not to interfere with subscripts with other meanings. (For example, *x*^{(n+1)} = *f*(*x*^{(n)}).) If the function *f* is continuously differentiable, a sufficient condition for convergence is that the spectral radius of the derivative is strictly bounded by one in a neighborhood of the fixed point. If this condition holds at the fixed point, then a sufficiently small neighborhood (basin of attraction) must exist.

## Linear systems

In the case of a system of linear equations, the two main classes of iterative methods are the **stationary iterative methods**, and the more general Krylov subspace methods.

### Stationary iterative methods

#### Introduction

Stationary iterative methods solve a linear system with an operator approximating the original one; and based on a measurement of the error in the result (the residual), form a "correction equation" for which this process is repeated. While these methods are simple to derive, implement, and analyze, convergence is only guaranteed for a limited class of matrices.

#### Definition

An *iterative method* is defined by

and for a given linear system with exact solution the *error* by

An iterative method is called *linear* if there exists a matrix such that

and this matrix is called *iteration matrix*.
An iterative method with a given iteration matrix is called *convergent* if the following holds

An important theorem states that for a given iterative method and its iteration matrix it is convergent if and only if its spectral radius is smaller than unity, that is,

The basic iterative methods work by splitting the matrix into

and here the matrix should be easily invertible. The iterative methods are now defined as

From this follows that the iteration matrix is given by

#### Examples

Basic examples of stationary iterative methods use a splitting of the matrix such as

where is only the diagonal part of , and is the strict lower triangular part of . Respectively, is the upper triangular part of .

- Richardson method:
- Jacobi method:
- Damped Jacobi method:
- Gauss–Seidel method:
- Successive over-relaxation method (SOR):
- Symmetric successive over-relaxation (SSOR):

Linear stationary iterative methods are also called relaxation methods.

### Krylov subspace methods

Krylov subspace methods work by forming a basis of the sequence of successive matrix powers times the initial residual (the **Krylov sequence**).
The approximations to the solution are then formed by minimizing the residual over the subspace formed.
The prototypical method in this class is the conjugate gradient method (CG) which assumes that the system matrix is symmetric positive-definite.
For symmetric (and possibly indefinite) one works with the minimal residual method (MINRES).
In the case of not even symmetric matrices methods, such as the generalized minimal residual method (GMRES) and the biconjugate gradient method (BiCG), have been derived.

#### Convergence of Krylov subspace methods

Since these methods form a basis, it is evident that the method converges in *N* iterations, where *N* is the system size. However, in the presence of rounding errors this statement does not hold; moreover, in practice *N* can be very large, and the iterative process reaches sufficient accuracy already far earlier. The analysis of these methods is hard, depending on a complicated function of the spectrum of the operator.

### Preconditioners

The approximating operator that appears in stationary iterative methods can also be incorporated in Krylov subspace methods such as GMRES (alternatively, preconditioned Krylov methods can be considered as accelerations of stationary iterative methods), where they become transformations of the original operator to a presumably better conditioned one. The construction of preconditioners is a large research area.

### History

Probably the first iterative method for solving a linear system appeared in a letter of Gauss to a student of his. He proposed solving a 4-by-4 system of equations by repeatedly solving the component in which the residual was the largest.

The theory of stationary iterative methods was solidly established with the work of D.M. Young starting in the 1950s. The Conjugate Gradient method was also invented in the 1950s, with independent developments by Cornelius Lanczos, Magnus Hestenes and Eduard Stiefel, but its nature and applicability were misunderstood at the time. Only in the 1970s was it realized that conjugacy based methods work very well for partial differential equations, especially the elliptic type.

## References

- Amritkar, Amit; de Sturler, Eric; Świrydowicz, Katarzyna; Tafti, Danesh; Ahuja, Kapil (2015). "Recycling Krylov subspaces for CFD applications and a new hybrid recycling solver".
*Journal of Computational Physics*.**303**: 222. arXiv:1501.03358. Bibcode:2015JCoPh.303..222A. doi:10.1016/j.jcp.2015.09.040.

## External links

Wikimedia Commons has media related to .Iterative methods |