A20 line

The A20, or addressing line 20, is one of the electrical lines that make up the system bus of an x86-based computer system. The A20 line in particular is used to transmit the 21st bit on the address bus.

A microprocessor typically has a number of addressing lines equal to the base-two logarithm of its physical addressing space. For example, a processor with 4 GB of byte-addressable physical space requires 32 lines, which are named A0 through A31. The lines are named after the zero-based number of the bit in the address that they are transmitting. The least significant bit is first and is therefore numbered bit 0 and signaled on line A0. A20 transmits bit 20 (the 21st bit) and becomes active once addresses reach 1 MB, or 220.

History

The Intel 8086, Intel 8088, and Intel 80186 processors had 20 address lines, numbered A0 to A19; with these, the processor can access 220 bytes, or 1 MB. Internal address registers of such processors only had 16 bits. To access a 20-bit address space, an external memory reference was made up of a 16-bit offset address added to a 16-bit segment number, shifted 4 bits so as to produce a 20-bit physical address. The resulting address is equal to segment × 16 + offset.[1] There are many combinations of segment and offset that produce the same 20-bit physical address. Therefore, there were various ways to address the same byte in memory. For example, here are four of the 4096 different segment:offset combinations, all referencing the byte whose physical address is 0x000FFFFF (the last byte in 1 MB-memory space):

F000:FFFF
FFFF:000F
F555:AAAF
F800:7FFF

Referenced the last way, an increase of one in the offset yields F800:8000, which is a proper address for the processor, but since it translates to the physical address 0x00100000 (the first byte over 1 MB), the processor would need another address line for actual access to that byte. Since there is no such line on the 8086 line of processors, the 21st bit above, while set, gets dropped, causing the address F800:8000 to "wrap around"[1] and to actually point to the physical address 0x00000000.

To save program space,[1] a trick was used by some BIOS and DOS programmers, for example, to have one segment that has access to program data (such as from F800:0000 to F800:7FFF, pointing to the physical addresses 0x000F8000–0x000FFFFF), as well as the I/O data (such as the keyboard buffer) that was located in the first memory segment (with addresses F800:8000 to F800:FFFF pointing to the physical addresses 0x00000000 to 0x00007FFF). This trick was utilized by IBM/Microsoft Pascal itself as well as by programs compiled with it,[2][3][4][5] including Microsoft's MASM.[5] Other commonly used development utilities using this were executable compressors like Realia's Spacemaker[6] (written by Robert B. K. Dewar in 1982 and used to compress early versions of the Norton Utilities[7][8][9][10]) and Microsoft's EXEPACK[6][1][11][5] (written by Reuben Borman in 1985) as well as the equivalent /E[XEPACK] option in Microsoft's LINK 3.02 and higher.[1][11][9] The SPELL utility in Microsoft's Word 3.0 was affected as well.[12] The address wrap was also used by MS-DOS itself, to implement the CALL 5 entry point in the Program Segment Prefix; the CALL 5 handler was at physical address 0x000000C0, but for CP/M compatibility, its offset had to match the segment size (usually 0xFEF0). The only way to reconcile them was to choose a segment value that when added to 0xFEF0, resulted in a physical address of 0x001000C0, which would wrap around to 0x000000C0.

When IBM designed the IBM PC AT machine, it decided to use the new higher-performance Intel 80286 microprocessor. The 80286 could address up to 16 MB of system memory in protected mode. However, the CPU was supposed to emulate an 8086's behavior in real mode, its startup mode, so that it could run operating systems and programs that were not written for protected mode. The 80286 did not force the A20 line to zero in real mode, however. Therefore, the combination F800:8000 would no longer point to the physical address 0x00000000, but to the correct address 0x00100000. As a result, some DOS programs would no longer work, f.e. programs processed with EXEPACK would display a "Packed file is corrupt" error message.[1][11] To remain compatible with such programs, IBM decided to correct the problem on the motherboard.

That was accomplished by inserting a logic gate on the A20 line between the processor and system bus, which got named Gate-A20. Gate-A20 can be enabled or disabled by software to allow or prevent the address bus from receiving a signal from A20. It is set to non-passing for the execution of older programs that rely on the wrap-around. At boot time, the BIOS first enables Gate-A20 when it counts and tests all of the system memory, and then disables it before transferring control to the operating system.

Originally, the logic gate was a gate connected to the Intel 8042 keyboard controller.[1] Controlling it was a relatively slow process. Other methods have since been added to allow more efficient multitasking of programs that require this wrap-around with programs that access all of the system memory. There are multiple methods to control the A20 line.[13]

Disconnecting A20 would not wrap all memory accesses above 1 MiB, just those in the 1–2 MiB, 3–4 MiB, 5–6 MiB, etc. ranges. Real-mode software cared only about the area slightly above 1 MiB, so the Gate-A20 line was enough.

Enabling the Gate-A20 line is one of the first steps that a protected-mode x86 operating system does in the bootup process, often before control has been passed to the kernel from the bootstrap (in the case of Linux, for example).

Virtual 8086 mode, introduced with the Intel 80386, allows the A20 wrap-around to be simulated by using the virtual memory facilities of the processor; physical memory may be mapped to multiple virtual addresses. Thus, the memory mapped at the first mebibyte of virtual memory may be mapped again in the second mebibyte of virtual memory. The operating system may intercept changes to Gate A20 and make corresponding changes to the virtual-memory address space, which also makes irrelevant the efficiency of Gate-A20 line toggling.

A20 gate

Controlling the A20 line was an important feature at one stage in the growth of the IBM PC architecture, as it added access to an additional 65,520 bytes (64 KiB − 16 B) of memory in real mode, without significant software changes.

In what was arguably a "hack", the A20 gate was originally part of the keyboard controller on the motherboard, which could open or close it depending on what behavior was desired.[14]

The A20 gate is still present on many modern PCs, and the gate is initially closed right after boot. Modern protected-mode operating systems typically open the A20 gate early during the boot process and never close it again. Such operating systems do not have the compatibility reasons for keeping it closed, and they gain access to the full range of physical addresses available by opening it.

The Intel 80486 and Pentium added a special pin named A20M#, which when asserted low forces bit 20 of the physical address to be zero for all on-chip cache- or external-memory accesses. It was necessary, since the 80486 introduced an on-chip cache and so masking this bit in external logic was no longer possible. Software still needs to manipulate the gate and must still deal with external peripherals (the chipset) for that.[15]

Support for the A20 gate was changed in the Nehalem microarchitecture (some sources incorrectly claim that A20 support was removed). Rather than the CPU having a dedicated A20M# pin that receives the signal whether or not to mask the A20 bit, it has been virtualized so that the information is sent from the peripheral hardware to the CPU using special bus cycles. From a software point of view, the mechanism works exactly as before, and an operating system must still program external hardware (which in-turn sends the aforementioned bus cycles to the CPU) to disable the A20 masking.

Intel no longer supports the A20 gate, starting with Haswell. Page 271 of the Intel System Programmers Manual Vol. 3A from June 2013 states: "The functionality of A20M# is used primarily by older operating systems and not used by modern operating systems. On newer Intel 64 processors, A20M# may be absent."[16]

A20 handler

The A20 handler is IBM PC memory manager software that controls access to the high memory area (HMA). Extended-memory managers usually provide this functionality. A20 handlers are named after the 21st address line of the microprocessor, the A20 line.

In DOS, HMA managers such as HIMEM.SYS have the "extra task" of managing A20. HIMEM.SYS provided an API for opening/closing A20. DOS itself could use the area for some of its storage needs, thereby freeing up more conventional memory for programs. That functionality was enabled by the DOS=HIGH or HIDOS=ON directives in the CONFIG.SYS configuration file.

See also

References

  1. Paul, Matthias R. (2002-02-02). "Treiber dynamisch nachladen (Intra-Segment-Offset-Relokation zum Laden von TSRs in die HMA)" [Loading drivers dynamically (Intra-segment offset relocation to load TSRs into the HMA)] (in German). Newsgroup: de.comp.os.msdos. Archived from the original on 2017-09-09. Retrieved 2017-07-02. (NB. Gives a comprehensive overview on the history and "nature" of the HMA and the non-obvious design constraints to be observed when developing resident system extensions to be loaded into the HMA, some of which are caused by the A20 gate. It also describes how to address these issues using stubs, backdoors, and intra-segment offset relocation, a method used by DR-DOS drivers capable of relocating into the HMA and similar to a (more sophisticated) method used as the basis for the dynamic dead code elimination in the author's FreeKEYB driver.)
  2. Letwin, James (1985-04-10). "Method and operating system for executing programs in a multi-mode microprocessor". Microsoft. US06722052, US4779187A. Archived from the original on 2018-09-23. Retrieved 2018-09-23. […] Some programs written for the 8086 rely on [address wrap-around] to run properly. Unfortunately, memory locations extend above 1 megabyte in the real mode of the 80286 and are not wrapped to low memory locations. Consequently, programs including those written in MicroSoft PASCAL and programs which use the "Call 5" feature of MS-DOS will fail on the standard 80286 system. […] For example, no PASCAL programs are loaded into memory below 64K, and a special instruction is placed in the lower memory locations above 1 megabyte–for example, address 100000h or 100010h. […]
  3. Pascal Compiler (PDF). Personal Computer Computer Language Series (1 ed.). International Business Machines Corporation. August 1981. Retrieved 2018-09-23.
  4. "NAME ENTX - Microsoft MS-DOS Computer Pascal runtime system control". 1.00. Microsoft Corp. 1981. Archived from the original on 2018-09-23. Retrieved 2018-09-23. […] DX is final DS (may be negative) […] final DS value (may be negative) […]
  5. Necasek, Michal (2018-03-16). "The A20-Gate: It Wasn't WordStar". OS/2 Museum. Archived from the original on 2018-09-23. Retrieved 2018-09-23.
  6. Paul, Matthias R. (2002-10-07) [2000]. "Re: masm .com (PSP) related trouble". Newsgroup: alt.lang.asm. Archived from the original on 2017-09-03. Retrieved 2017-09-03.
  7. "Expert Report of Robert B. K. Dewar In Response To The Report Of Kenneth D. Crews". Cambridge University Press et al v. Patton et al, Filing 124, Supplemental Initial Disclosures by Cambridge University Press, Oxford University Press, Inc., Sage Publications, Inc. - Cambridge University Press, Oxfort University Press, Inc., and Sage Publications, Inc. v. Mark P. Becker, Georgia State University President, et al, Civil Action No. 1:08-CV-1425-ODE (Court document). United States District Court For The Northern District Of Georgia, Atlanta Division. p. 18. Exhibit A. Archived from the original on 2018-05-01. Retrieved 2019-04-23. […] SPACEMAKER and TERMULATOR, commodity software for IBM PC (PC DOS file compression utility and VT-100 emulator), being marketed by Realia, Inc. R.B.K. Dewar (1982-1983), 8088 assembly language, 8,000 lines […]
  8. Realia, Inc. (January 1983). "If you use DOS, you need this program". PC Magazine (advertisement). Ziff-Davis Publishing. 2 (9): 417. Archived from the original on 2019-04-22. Retrieved 2019-04-22.
  9. Dewar, Robert Berriedale Keith (1984-03-13). "DOS 3.1 ASMB (Another Silly Microsoft Bug)". info-ibmpc@USC-ISIB.ARPA. Archived from the original on 2018-05-01. Retrieved 2019-04-23. […] The /E option of the linker should generate an EXE file which is logically equivalent to the uncompressed EXE file. The current version […] results in AX being clobbered. AX on entry to an EXE file has a definite meaning (it indicates drive validity for the parameters), thus it should be passed through to the uncompressed image. Given this one very obvious violation of the interface rules, there may be others, I have not bothered to investigate further […] I did write the Realia SpaceMaker program which does a similar sort of thing to the EXEPACK option (but needless to say does not have this particular […]
  10. Necasek, Michal (2018-04-30). "Realia SpaceMaker". OS/2 Museum. Archived from the original on 2019-01-27. Retrieved 2019-02-22.
  11. Necasek, Michal (2018-03-23). "EXEPACK and the A20-Gate". OS/2 Museum. Archived from the original on 2018-11-13. Retrieved 2019-04-20.
  12. Parsons, Jeff (2018-05-27) [1987-12-01, 1987-08-02]. "Somebody Put a SPELL On Me". PCjs. Archived from the original on 2019-01-29. Retrieved 2019-04-21.
  13. "A20 Line". OSDev Wiki.
  14. Shanley, Tom; Anderson, Don; Swindle, John (1995). ISA system architecture. Addison-Wesley. pp. 79–80. ISBN 0-201-40996-8.
  15. Shanley, Tom (1996). Protected mode software architecture. Taylor & Francis. p. 60. ISBN 0-201-55447-X.
  16. Intel System Programmers Manual Vol. 3A from June 2013.

Further reading

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.